Sponsored Content
Operating Systems Linux Ubuntu Linux LVM.. Grub not loading from replaced disk Post 302862633 by busyboy on Friday 11th of October 2013 06:50:07 AM
Old 10-11-2013
Hi,

i have created a Grub Partition on the disk drive as it recommended in a Guide

I have two 3 TB disks with mirroring. Is there anything related to creating the disk replication and then attaching it or something else?

Regards,
NMR
 

10 More Discussions You Might Find Interesting

1. HP-UX

disk adding through lvm

Hi dear(s) Can u explain how to add a disk through lvm with commands. I need to add a 9 gb scsi HS disk to a Hp D class 9000 server. (2 Replies)
Discussion started by: sreekumar.R
2 Replies

2. UNIX for Dummies Questions & Answers

GRUB and booting from LVM volumes?

I'm setting-up my new computer, and would like to try out and switch between several OS (mostly different Linux distros). As I prefer to use separate partition for various dirs (/, home, usr, var, opt and perhaps local), I've come to the conclution that I'll run-out of partitions too soon, so I've... (1 Reply)
Discussion started by: koppe
1 Replies

3. UNIX for Advanced & Expert Users

grub loading stage 1.5.

Hi people,I am trying to install Debian Lenny Betta-2 on a system that has the built in promise chip for "Raid 0" but when I finished the install and then I reboot ,I get "grub loading,pleas wate... Error 2. also the Debian Lenny Betta-2 is identifying both drives ,instead of a singular drive... (4 Replies)
Discussion started by: thegreatalsky
4 Replies

4. AIX

Disk I/O Issue using LVM

We have a filesystem which contains 8 hard disks but i am facing disk I/O issue becuase data is not spreading across all the disks.Is there any way i can check how data is spreading and any parameter we need to change to spread ata across all disks. OS--AIX 5.3 (1 Reply)
Discussion started by: ukatru
1 Replies

5. Red Hat

Grub is not loading the correct kernel

All I am trying to get RHEL 5.4 to load to the XEN enabled kernel but I am not having much luck. My grub.conf looks like it has 2.6.18-194.11.3.el5xen as the 1st one but when I do a uname -a I get the NON xen enabled kernel. I know I am doing something stupid but if anybody has any... (1 Reply)
Discussion started by: razor3928
1 Replies

6. Solaris

Veritas not attaching replaced disk

Hi, I`m on SunFire480R with Solaris 10. Disk in rootdg group failed, so it was replaced. However, I cannot make Veritas initalise the replaced disk: # vxdctl enable # vxdisk list c1t0d0s2 Device: c1t0d0s2 devicetag: c1t0d0 type: auto flags: online error private autoconfig... (1 Reply)
Discussion started by: masloff
1 Replies

7. Linux

Grub not loading from replaced disk

Hi, a little while ago, one of the GPT Partitioned hard disk had gone faulty in a Mirror RAID and is now successfully replaced. here is how I did that. 1) created identical partition table on the new disk. 2) attached the mirrors using md commands. The whole procedure is given below:... (2 Replies)
Discussion started by: busyboy
2 Replies

8. HP-UX

LVM: is possible to replace a disk?

Scenario1: VG00 lvm,not mirrored,2 disk of 36GB vg size VG00 size is under 30G. Is possible to remove a disk of 36GB and replace "on fly" with a disk of 300GB on VG00? Thanks (6 Replies)
Discussion started by: Linusolaradm1
6 Replies

9. UNIX for Advanced & Expert Users

LVM, Troubles with adding another Disk

I am having trouble with LVM and one of my physical volumes. Using Ubuntu Desktop 14.04 I was trying to set up LVM across two disks (not containing the OS or Home). First I created the initial Physical Volume, the Volume Group, and the Logical volume, and everything seemed fine. The... (2 Replies)
Discussion started by: JR_ULFOR
2 Replies

10. AIX

Replaced pdisk not showing up in SAS Disk Array Configuration

OSLevel: 5300-10-02-0943 System Model: IBM,8203-E4A Power 6 == Hi! I replaced a failed pdisk in the raid enclosure as follows, - rmdev -l 'pdisk18' '-d' - Replaced it. - cfgmgr (detected) - I can see the new drive, with the correct serial # lscfg -v -l pdisk18 pdisk18... (2 Replies)
Discussion started by: estrar
2 Replies
HD(4)							     Linux Programmer's Manual							     HD(4)

NAME
hd - MFM/IDE hard disk devices DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave hdd. General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order the partitions are discovered, and only nonempty, nonextended partitions get a number. However, partition numbers 1-4 are given to the four partitions described in the MBR (the "primary" partitions), regardless of whether they are unused or extended. Thus, the first logi- cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions on an IDE disk. For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS "primary" partition on the second one. They are typically created by: mknod -m 660 /dev/hda b 3 0 mknod -m 660 /dev/hda1 b 3 1 mknod -m 660 /dev/hda2 b 3 2 ... mknod -m 660 /dev/hda8 b 3 8 mknod -m 660 /dev/hdb b 3 64 mknod -m 660 /dev/hdb1 b 3 65 mknod -m 660 /dev/hdb2 b 3 66 ... mknod -m 660 /dev/hdb8 b 3 72 chown root:disk /dev/hd* FILES
/dev/hd* SEE ALSO
chown(1), mknod(1), sd(4), mount(8) COLOPHON
This page is part of release 3.53 of the Linux man-pages project. A description of the project, and information about reporting bugs, can be found at http://www.kernel.org/doc/man-pages/. Linux 1992-12-17 HD(4)
All times are GMT -4. The time now is 06:52 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy