10-10-2013
Thanks.. Yes we are anticipating good results.
9 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
now, what do you define as core files.
there are some files outthere with the name perl.core, I-core.png, core.png
I mean, are these classified as core files too??? i thought core files are simply files called "core". Please help me out
this is urgent (2 Replies)
Discussion started by: TRUEST
2 Replies
2. Solaris
Setting up a T5240 with two disks c1t0d0 and c1t1d0.
I am trying to use raidctl but when I issue.
raidctl -l
I get
Controller 1
Disk: 0.0.0
Disk: 0.1.0
So I try
raidctl -c '0.0.0 0.1.0' -r 1 1
and I get "Array in use."
I try (4 Replies)
Discussion started by: photon
4 Replies
3. Solaris
its a fresh installation. during the OS setup, it did not prompt for IP, netmask and gateway. using Solaris 10 08/07 update 4. I tried to plumb manually but encountered no such interface error. but nxge interfaces can be greped from the /etc/path_to_inst file.
getting similar error on... (3 Replies)
Discussion started by: incredible
3 Replies
4. Solaris
Hi,
We are planning to buy new server for our data center. Sun T5240 or M3000 which one have better performance, we are going to create many dt sessions in this server. So, i need your suggestions.
RJS (4 Replies)
Discussion started by: rajasekg
4 Replies
5. Solaris
Hi Friends
we have sun T5240 server, we have taken ufsdump of this server remotely with scsi tapedrive, If we need to do ufsrestore means what we have to do, since T5240 has not having scsi port, any procedure is there?
Regards
Rajasekar (5 Replies)
Discussion started by: rajasekg
5 Replies
6. Solaris
Hi Gurus
Can any one tell me the process of disabling the multithreading option on T5240 server and my OS is on LDOM, having one physical processor with 8 core & 8 thread per core
Regards (3 Replies)
Discussion started by: amity
3 Replies
7. Solaris
Hi !
I've been given a T5240 with 4 disks and 2 HBA cards (but no array connected). I did a factory reset on SP and NVRAM clean on OBP because the server had been used before.
I boot cdrom in single mode and try to create a hw mirror with disks from c1... but only c2 is seen by raidctl.
... (2 Replies)
Discussion started by: delavega
2 Replies
8. Solaris
Hi
I need to reduce cores on T5240 server for meeting Oracle Core licenses. For that I have install the LDOM packages & run below mention commands.
bash-3.2# ldm list-config
factory-default
config_initial
bash-3.2# ldm set-vcpu 32 primary
bash-3.2# ldm list-config... (5 Replies)
Discussion started by: amity
5 Replies
9. Solaris
Hi Folks,
Just a quick question - hopefully!
I have an application currently running on a V890 with Solaris 9, I'd like to move this to either one of our T-5's or one of the T5240's in a Legacy container on an LDOM - but the fly in the ointment is the application still uses a standard Hayes... (3 Replies)
Discussion started by: gull04
3 Replies
LEARN ABOUT CENTOS
ldns-test-edns
ldns-test-edns(1) General Commands Manual ldns-test-edns(1)
NAME
ldns-test-edns - test if dns cache supports EDNS and DNSSEC.
SYNOPSIS
ldns-test-edns [ -i ] { ip }
DESCRIPTION
ldns-test-edns tests a DNS cache and checks if it supports EDNS0 and DNSSEC types so that it can be used as a dnssec-enabled DNS cache. It
sends two queries to the cache, one for the root key and one for a DS record. These must succeed, the answer must have EDNS, that type and
signatures.
If the IP address is good for DNSSEC, it is printed with 'OK'. Otherwise short description is given of the failure. If OK is given, the
cache should be good to use as a cache for a local configured DNSSEC validator.
The tool assumes the root is signed and Sweden is signed. Also, the queries are sent with the CD flag, the tool does not check that the
results are validated, but that they can be validated.
OPTIONS
-i option enables a mode where the working IP addresses are printed after another, with no other explanations, and if none work or no IP
addresses are on the input, 'off' is printed.
ldns-test-edns takes one or more IP addresses, it checks them in turn. IPv4 and IPv6 addresses can be given. The exit value is for the
last checked IP address: 0 is OK, 1 is failure, 2 is some sort of network failure.
AUTHOR
Written by the ldns team as an example for ldns usage.
REPORTING BUGS
Report bugs to <ldns-team@nlnetlabs.nl>.
COPYRIGHT
Copyright (C) 2010 NLnet Labs. This is free software. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR-
POSE.
14 Dec 2010 ldns-test-edns(1)