10-10-2013
Thanks.. Yes we are anticipating good results.
9 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
now, what do you define as core files.
there are some files outthere with the name perl.core, I-core.png, core.png
I mean, are these classified as core files too??? i thought core files are simply files called "core". Please help me out
this is urgent (2 Replies)
Discussion started by: TRUEST
2 Replies
2. Solaris
Setting up a T5240 with two disks c1t0d0 and c1t1d0.
I am trying to use raidctl but when I issue.
raidctl -l
I get
Controller 1
Disk: 0.0.0
Disk: 0.1.0
So I try
raidctl -c '0.0.0 0.1.0' -r 1 1
and I get "Array in use."
I try (4 Replies)
Discussion started by: photon
4 Replies
3. Solaris
its a fresh installation. during the OS setup, it did not prompt for IP, netmask and gateway. using Solaris 10 08/07 update 4. I tried to plumb manually but encountered no such interface error. but nxge interfaces can be greped from the /etc/path_to_inst file.
getting similar error on... (3 Replies)
Discussion started by: incredible
3 Replies
4. Solaris
Hi,
We are planning to buy new server for our data center. Sun T5240 or M3000 which one have better performance, we are going to create many dt sessions in this server. So, i need your suggestions.
RJS (4 Replies)
Discussion started by: rajasekg
4 Replies
5. Solaris
Hi Friends
we have sun T5240 server, we have taken ufsdump of this server remotely with scsi tapedrive, If we need to do ufsrestore means what we have to do, since T5240 has not having scsi port, any procedure is there?
Regards
Rajasekar (5 Replies)
Discussion started by: rajasekg
5 Replies
6. Solaris
Hi Gurus
Can any one tell me the process of disabling the multithreading option on T5240 server and my OS is on LDOM, having one physical processor with 8 core & 8 thread per core
Regards (3 Replies)
Discussion started by: amity
3 Replies
7. Solaris
Hi !
I've been given a T5240 with 4 disks and 2 HBA cards (but no array connected). I did a factory reset on SP and NVRAM clean on OBP because the server had been used before.
I boot cdrom in single mode and try to create a hw mirror with disks from c1... but only c2 is seen by raidctl.
... (2 Replies)
Discussion started by: delavega
2 Replies
8. Solaris
Hi
I need to reduce cores on T5240 server for meeting Oracle Core licenses. For that I have install the LDOM packages & run below mention commands.
bash-3.2# ldm list-config
factory-default
config_initial
bash-3.2# ldm set-vcpu 32 primary
bash-3.2# ldm list-config... (5 Replies)
Discussion started by: amity
5 Replies
9. Solaris
Hi Folks,
Just a quick question - hopefully!
I have an application currently running on a V890 with Solaris 9, I'd like to move this to either one of our T-5's or one of the T5240's in a Legacy container on an LDOM - but the fly in the ointment is the application still uses a standard Hayes... (3 Replies)
Discussion started by: gull04
3 Replies
LEARN ABOUT BSD
mkmanifest
MKMANIFEST(1) General Commands Manual MKMANIFEST(1)
NAME
mkmanifest - create a shell script to restore Unix filenames
SYNOPSIS
mkmanifest [ files ]
DESCRIPTION
Mkmanifest creates a shell script that will aid in the restoration of Unix filenames that got clobbered by the MSDOS filename restrictions.
MSDOS filenames are restricted to 8 character names, 3 character extensions, upper case only, no device names, and no illegal characters.
The mkmanifest program is compatible with the methods used in pcomm, arc, and mtools to change perfectly good Unix filenames to fit the
MSDOS restrictions.
EXAMPLE
I want to copy the following Unix files to a MSDOS diskette (using the mcopy command).
very_long_name
2.many.dots
illegal:
good.c
prn.dev
Capital
Mcopy will convert the names to:
very_lon
2xmany.dot
illegalx
good.c
xprn.dev
capital
The command:
mkmanifest very_long_name 2.many.dots illegal: good.c prn.dev Capital > manifest
would produce the following:
mv very_lon very_long_name
mv 2xmany.dot 2.many.dots
mv illegalx illegal:
mv xprn.dev prn.dev
mv capital Capital
Notice that "good.c" did not require any conversion, so it did not appear in the output.
Suppose I've copied these files from the diskette to another Unix system, and I now want the files back to their original names. If the
file "manifest" (the output captured above) was sent along with those files, it could be used to convert the filenames.
SEE ALSO
arc(1), pcomm(1), mtools(1)
local MKMANIFEST(1)