I'm trying to make a backup of a directory tree on Solaris 8. I'm doing this with my own ID, not root. The problem I am running into is when I extract the archive, all files are owned by me and the group is my default group. The man page lists this as the default behavior when executed by a... (1 Reply)
Hi all,
I am caught up in a problem .... tried all possible ways i knew .. but ended up in big zero ... ;-(
I have a file as below ..
$ cat siv.txt
1234567890BF00522000095ibsadministrator@ae.ge.com ibsadministrator@ae.ge.com
Note the spaces in between .... I am... (1 Reply)
I am a 10 years windows person with basic unix training (very basic).
I have a sco server where it originally had 3 physical drives. Drive 0 had to be replaced so I did that but because I am really new to Unix I was afraid to detroy the data on DRIVE 1 and 2, so I took them out when I loaded the... (3 Replies)
I obviously haven't learned my lesson with shell and whitespace.
find /path/to/some/where/ -name "*.pdf" | awk '{print $5}'| uniq -d
results:
some Corporation
other Corporate junk
firmx
Works fine from cmdline but the whitespace turns into another FS in a for loop.
for... (7 Replies)
I'm trying to get a number of old disks on HP-UX 10.2 copied over to a new Debian machine which has a NAS on it.
The HP does not have rsync, but does have scp. Scp unfortunately does not always preserve permissions, and does not save links which were on the disk.
Apparently rsync has a flag... (3 Replies)
I'm trying to get a number of old disks on HP-UX 10.2 copied over to a new Debian machine which has a NAS on it.
The HP does not have rsync, but does have scp. Scp unfortunately does not always preserve permissions, and does not save links which were on the disk.
Apparently rsync has a flag... (2 Replies)
Hi guys,
I'm trying to unzip a file and rename it to another while preserving the original timestamp:
$ cat file.dat.gz | gzip -d > newfile.dat
My goal is to assign the file.dat.gz timestamp to newfile.dat.
I cannot use gunzip, due to various checks done with wget. Basically, I have to... (1 Reply)
Below is the issue I am having.
I have a few variables which have certain values in them like
var1=23
var2=46
var3=78 etc...
I want to save these values with the help of a for loop in a single variable so that I can use it later,beacuse a few lines down the script, some of these... (3 Replies)
In a nutshell, I want $USER to reflect my user ID in a script run with sudo. I'm working with OSX in case that makes a difference.
If I 'sudo echo $USER', I get my user ID. But if I 'sudo myscript.sh' and myscript.sh has a line to echo $USER, I get 'root' I'm hoping there's a switch I can add... (1 Reply)
Hello:
I have the following HTML table:
<table>
<thead>
<tr>
<th>Code</th>
<th>Percentage</th>
</tr>
</thead>
<tbody>
<tr>
<td>1</td>
<td>30%</td>
</tr>
<tr>
<td>2</td>
... (3 Replies)
Discussion started by: Cacializ
3 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)