09-10-2013
See
here for some alternate methods of entering your BIOS.
And
here for BIOS recovery in an Acer laptop.
Hope it helps.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Can a hard drive be formatted from unix server to windows 2000 professional? (4 Replies)
Discussion started by: howarddtp
4 Replies
2. UNIX for Advanced & Expert Users
I have the following system:
- DELL Dimension 8300
- Pentium IV @ 2.66GHz
- BIOS Revision A07
- 1.5GB RAM
- 2 Hard Disks (Master 120GB, Slave 80GB), I guess it's IDE
I had WinXP on the master disk (hd0) and recently installed Solaris 10 1/06 on the slave disk (hd1). The NTLDR is in MBR... (0 Replies)
Discussion started by: Hawk
0 Replies
3. Solaris
I'm in the process of scrubbing a tonne of hard drives. Having a few problems with my formatting.
I've been following http://www.sun.com/blueprints/0600/scrub.pdf however on the steps of
#format> format
Ready to format. Formatting cannot be interrupted
and takes 100 minutes (estimated).... (0 Replies)
Discussion started by: Jamiee
0 Replies
4. Filesystems, Disks and Memory
Hello,
I wanted to share an experience I had today which was quite a learning experience and perhaps useful for others who may run into the issue at some point in the future.
Basically, the scenario involves a OS which was installed on a machine which hardware-wise, had a SATA Drive. The... (0 Replies)
Discussion started by: septima.pars
0 Replies
5. SCO
hi
I've a fresh installation of SCO 5.0.7 on the IDE hard disk.
For SCSI hard disk I can declare, for example blc disk driver using:
# mkdev hd 0 SCSI-0 0 blc 0but it works for IDE hard disk? (3 Replies)
Discussion started by: ccc
3 Replies
6. Linux
Hi all,
I'm kind of new to programming in Linux & c/c++. I'm currently writing a FileManager using Ubuntu Linux(10.10) for Learning Purposes. I've got started on this project by creating a loopback device to be used as my virtual hard disk. After creating the loop back hard disk and mounting it... (23 Replies)
Discussion started by: shen747
23 Replies
7. Solaris
I changed disk controller. Unplugged every disk, inserted another controller card, an IBM M1015. The disks are recognized in BIOS, and the controller card's BIOS shows up. But after that, I drop into GRUB and a prompt. That is all.
How shall I solve this problem? I am thinking of booting from... (2 Replies)
Discussion started by: kebabbert
2 Replies
8. UNIX for Advanced & Expert Users
pls help me how to load debian again after un-TARing the debian backup on a newly formated Hard Disk (ext3)
am using DEBIAN LENNY 64 bit. (4 Replies)
Discussion started by: coolatt
4 Replies
9. Linux
Hi,
a little while ago, one of the GPT Partitioned hard disk had gone faulty in a Mirror RAID and is now successfully replaced.
here is how I did that.
1) created identical partition table on the new disk.
2) attached the mirrors using md commands.
The whole procedure is given below:... (2 Replies)
Discussion started by: busyboy
2 Replies
10. Solaris
I installed x86 Solaris 10 update 10 after Windows XP, later I removed xp and installed Debian 9 stretch on the same partition but, Debian couldn't find any other os so it deleted Solaris 10 grub or did something like that I couldn't got.
I thought I would be able to recover the lost record by... (0 Replies)
Discussion started by: vectrum
0 Replies
LEARN ABOUT MINIX
httppower
httppower(8) powerman httppower(8)
NAME
httppower - communicate with HTTP based power distribution units
SYNOPSIS
httppower [--url URL]
DESCRIPTION
httppower is a helper program for powerman which enables it to communicate with HTTP based power distribution units. It is run interac-
tively by the powerman daemon.
OPTIONS
-u, --url URL
Set the base URL.
INTERACTIVE COMMANDS
The following commands are accepted at the httppower> prompt:
auth user:pass
Authenticate to the base URL with specified user and password, using ``basic'' HTTP authentication which sends the user and password
over the network in plain text.
seturl URL
Set the base URL. Overrides the command line option.
get [URL-suffix]
Send an HTTP GET to the base URL with the optional URL-suffix appended.
post [URL-suffix] key=val[&key=val]...
Send an HTTP POST to the base URL with the optional URL-suffix appended, and key-value pairs as argument.
FILES
/usr/sbin/httppower
/etc/powerman/powerman.conf
ORIGIN
PowerMan was originally developed by Andrew Uselton on LLNL's Linux clusters. This software is open source and distributed under the terms
of the GNU GPL.
SEE ALSO
powerman(1), powermand(8), httppower(8), plmpower(8), vpcd(8), powerman.conf(5), powerman.dev(5), powerman-devices(7).
http://sourceforge.net/projects/powerman
powerman-2.3.5 2009-02-09 httppower(8)