Hi guys,
I need help in extracting one column of numbers from two different files and display it in a output file. In specific, I want to extrac the column no.2 ($2) from each file, file1.txt, file2.txt. Then place both extracted columns in a one file, out.txt.
the line command I use to... (7 Replies)
Suppose i have a file A
1*2*3*4
2*4*4*22
and second file B
2*3*4*5
4*4*6*7
By multiplying file A by file B that is file A by first column in file B respectively
output shud be
2*6*12*20
8*16*24*154
my code is
=$1
next
}
{for (f=1;f<=NF;f++) (2 Replies)
Hi,
i have file1 which looks like:
x1 y1 z1
x2 y2 z2
...(and so on)
and file2 which looks like:
a11 a12 a13
a21 a22 a23
a31 a32 a33
and i want to replace file1 with the following values:
x1' y1' z1'
x2' y2' z2'
...(and so on) (2 Replies)
Hi,
This is something that probably it is more difficult to explain than to do.
I have two files e.g.
FILE1
A15 8.3102E+00 3.2000E-04
A15 8.5688E+00 4.3000E-05
B13 5.1100E-01 1.9960E+00
B16 5.1100E-01 2.3000E-03
B16 8.6770E-01 1.0000E-07
B16 9.8693E-01 3.4000E-05... (4 Replies)
Hi,
I have 2 ASCII files, say
file1
AAAAA 3.465830E-12
BBBBB 4.263280E-08
CCCCC 1.113320E-17
DDDDD 0.000000E+00
...
file2 with as many lines as file1
3.932350E-12
1.194380E-07
4.901480E-17
0.000000E+00
3.921180E-40 (3 Replies)
I need to multiply column1 and column3 data and need to compare it with column5. Need to check multiplication and Throw error if result is greater or less than column5 values, though difference of +/- 2 will be ok
Ex - if column1 has 2.4 and column3 has 3.5, it will be ok if column5 have value... (13 Replies)
Example:
I have files in below format
file 1:
zxc,133,joe@example.com
cst,222,xyz@example1.com
File 2 Contains:
hxd
hcd
jws
zxc
cst
File 1 has 50000 lines and file 2 has around 30000 lines :
Expected Output has to be :
hxd
hcd
jws (5 Replies)
Discussion started by: TestPractice
5 Replies
LEARN ABOUT DEBIAN
sc_warts2text
SC_WARTS2TEXT(1) BSD General Commands Manual SC_WARTS2TEXT(1)NAME
sc_warts2text -- simple dump of information contained in a warts file.
SYNOPSIS
sc_warts2text [-d ip2descr-file] [file ...]
DESCRIPTION
The sc_warts2text utility provides a simple dump of information contained in a sequence of warts files. The output is the same as that which
would have been provided by scamper if the text output option had been chosen instead of the warts output option when the data was collected.
The options are as follows:
-d ip2descr-file
specifies the name of a file with IP-address, description mappings, one mapping per line. See the examples section for further
information.
While the output of sc_warts2text is structured and suitable for initial analyses of results, the format of the output is not suitable for
automated parsing and analysis as the output of sc_warts2text will change overtime with no regard to backwards compatibility. Analyses of
the contents of a warts file should be made using specialised programs which link against the scamper file API.
EXAMPLES
The command:
sc_warts2text file1.warts file2.warts
will decode and print the contents of file1.warts, followed by the contents of file2.warts.
The command:
gzcat file1.warts.gz | sc_warts2text
will print the contents of the uncompressed file supplied on stdin.
Given a set of IP-address, description pairs in a file name mappings.txt:
192.0.2.1 "foo"
192.0.2.2 "bar"
then the command gzcat file1.warts.gz | sc_warts2text -d mappings.txt will print the description associated with a given destination address
before each result is presented.
SEE ALSO scamper(1), sc_wartsdump(1)AUTHORS
sc_warts2text is written by Matthew Luckie <mjl@luckie.org.nz>.
BSD October 15, 2010 BSD