If you're a beginner this may be easier to set up with a GUI like network-manager-gnome or network-manage-kde, depending on your desktop.
You may want to ensure this connection works without encryption turned on first. If this fails you would want to ensure vmware is detecting the card and determine if this is a vmware problem or a Linux problem.
If you are getting a connection with another interface like eth0 you may want to turn it off first, then bring up wlan0 or whatever interface it comes up on and run dhclient like so:
First of all, Happy Holidays,Merry Xmas, Happy Hanakah, Happy Kwanzaa, Happy Mid Winter Festival, etc.(Forgive me if I left your holiday out)
Anyway, here is my situation. I am setting up an email server at the job, and Sendmail is not cooperating. The error that I get on my RedHat 7.3 Dell... (5 Replies)
I had just instal freebsd in my computer, wich is very nice,am very happy about it, am new to the unix os and i know unmost nothing and my problem is that i din't do i good configuration because i can get internet when i open the webbrowser, a have a yahoo dsl connection, i can't even play a cd in... (0 Replies)
is me again guys, sorry for the mistake in the written, what the problem is, i can't connect to the internet because i did a bad configuration in the freebsd os, i use a yahoo dsl modem and i don't dial to my isp, but everytime i try to connect ask me for a phone number to connect to my isp, what... (1 Reply)
Hello.
I'm currently usng Solaris 10 and have to configure the box so that it acts as an FTP server handling multiple virtual domains. This should be done using wu-ftpd.
I have successfully configured the box to be able to handle multiple virtual FTP servers, and all works well when I log in as... (2 Replies)
Hi,
I have a strange problem. we're trying to connect an IBM pseries, to a Brocade switch, for SAN acess, using a badged emulex card, (IBM FC6239) WE can configure the device to see the fabric. The only problem we have is that the Brocade sees the HBA as storage, and not as a HBA.
We've zoned... (1 Reply)
Is there a time limit ifconfig wlan0 down? I used that command to take my wireless down.
sudo ifconfig wlan0 downWhen I came back about 6 hours later it was working without me bringing my wireless back up. I am the only one that uses my computer or that knows the root password. (0 Replies)
Hi All,
Am using Toshiba Satellite C850-l5212 Laptop . I have installed RHEL6 server on it ( Linux 2.6.32-220.el6.x86_64 )
I Installed wireless driver ( linux_mac80211_0012.0207.2013.tar.bz2 ) and the installation went fine.
But when i do ifconfig wlan0 up its giving the below error .... (0 Replies)
Dear Moderator,
While working on airmon-ng when the situation has come to set wlan0 on monitor mode
Identification Wlan0
root@kali:~# iwconfig
lo no wireless extensions.
wlan0 IEEE 802.11bgn ESSID:off/any
Mode:Managed Access Point: Not-Associated ... (1 Reply)
I have created a bridge with nmcli between eth0 and wlan0
I use this procedure
sudo nmcli con add ifname br0 type bridge con-name br0
sudo nmcli con add type bridge-slave ifname eth0 master br0
sudo nmcli con add type bridge-slave ifname wlan0 master br0
sudo nmcli con modify br0... (1 Reply)
Discussion started by: Linusolaradm1
1 Replies
LEARN ABOUT FREEBSD
mwl
MWL(4) BSD Kernel Interfaces Manual MWL(4)NAME
mwl -- Marvell 88W8363 IEEE 802.11n wireless network driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device mwl
device mwlfw
device wlan
device firmware
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_mwl_load="YES"
DESCRIPTION
The mwl driver provides support for IEEE 802.11n wireless network adapters based on Marvell 88W8363 parts. PCI and/or CardBus interfaces are
supported.
This driver requires the firmware built with the mwlfw module to work. Normally this module is loaded on demand by the driver but it may
also be compiled into the kernel.
Supported features include 802.11n, power management, BSS, MBSS, and host-based access point operation modes. All host/device interaction is
via DMA.
The mwl driver encapsulates IP and ARP traffic as 802.11 frames, however it can receive either 802.11 or 802.3 frames. Devices support
802.11n, 802.11a, 802.11g, and 802.11b operation with transmit speeds appropriate to each. The actual transmit speed used is dependent on
signal quality and the ``rate control'' algorithm implemented in the firmware. All chips have hardware support for WEP, AES-CCM, TKIP, and
Michael cryptographic operations.
The driver supports station, hostap, mesh, and wds mode operation. Multiple hostap virtual interfaces may be configured for simultaneous
use. When multiple interfaces are configured each may have a separate mac address that is formed by setting the U/L bits in the mac address
assigned to the underlying device. Any number of wds virtual interfaces may be configured together with hostap interfaces. Multiple station
interfaces may be operated together with hostap interfaces to construct a wireless repeater device. For more information on configuring this
device, see ifconfig(8).
Devices supported by the mwl driver come in either Cardbus or mini-PCI packages. Wireless cards in Cardbus slots may be inserted and ejected
on the fly.
EXAMPLES
Join an existing BSS network (ie: connect to an access point):
ifconfig wlan create wlandev mwl0 inet 192.168.0.20
netmask 0xffffff00"
Join a specific BSS network with network name ``my_net'':
ifconfig wlan create wlandev mwl0 inet 192.168.0.20
netmask 0xffffff00 ssid my_net"
Join a specific BSS network with WEP encryption:
ifconfig wlan0 create wlandev mwl0
ifconfig wlan0 inet 192.168.0.20 netmask 0xffffff00 ssid my_net
wepmode on wepkey 0x8736639624
Create an 802.11g host-based access point:
ifconfig wlan0 create wlandev mwl0 wlanmode hostap
ifconfig wlan0 inet 192.168.0.10 netmask 0xffffff00 ssid my_ap
mode 11g
Create an 802.11a mesh station:
ifconfig wlan0 create wlandev mwl0 wlanmode mesh
ifconfig wlan0 meshid my_mesh mode 11a inet 192.168.0.10/24
Create two virtual 802.11a host-based access points, one with WEP enabled and one with no security, and bridge them to the fxp0 (wired)
device:
ifconfig wlan0 create wlandev mwl0 wlanmode hostap
ssid paying-customers wepmode on wepkey 0x1234567890
mode 11a up
ifconfig wlan1 create wlandev mwl0 wlanmode hostap bssid
ssid freeloaders up
ifconfig bridge0 create addm wlan0 addm wlan1 addm fxp0 up
DIAGNOSTICS
mwl%d: unable to setup builtin firmware There was a problem downloading and/or setting up the firmware. The device is not usable.
mwl%d: failed to setup descriptors: %d There was a problem setting up the DMA data structures. This typically is caused by not being able
to allocate contiguous memory.
mwl%d: transmit timeout A frame dispatched to the hardware for transmission did not complete in time. This should not happen.
mwl%d: device not present A cardbus device was ejected while active; the request to the firmware was not completed.
SEE ALSO cardbus(4), intro(4), mwlfw(4), pci(4), wlan(4), wlan_ccmp(4), wlan_tkip(4), wlan_wep(4), wlan_xauth(4), hostapd(8), ifconfig(8),
wpa_supplicant(8)HISTORY
The mwl device driver first appeared in FreeBSD 8.0.
BUGS
The driver does not support power-save operation in station mode; consequently power use is suboptimal (e.g. on a laptop).
BSD July 8, 2009 BSD