Hi I was trying to mount my USB flashdrive on solaris 10 and I am getting the message saying that (I have already gone through the previous blogs in the forum)
mount: Block device required.
I have tried most of the possible ways.
#rmformat(gives me the necessary information about my flash... (1 Reply)
Hi all
A couple of new M5000 servers will be arriving soon and I need to work out how to configure the underlying domains.
It will come with 4 x CPUS, 32 Gb of memory, 4 x HD, 2 x IOtrays.
Reading the XSCF manual, I can configure the item into 2 domains, something about uni / quad xsb.... (9 Replies)
My previous post seems to be erased and I didn't get any help. I'm logged as root now but no mounting command seems to work, I've tried:
Mount -t vfat /dev/sdc1 /mnt/USB
Changing "sdc1" for hda1-7, and sdc1-7, and still nothing. Sometimes i get:
"special device not found" and others "device... (4 Replies)
I am very new to Solaris.
The machine I am working with is running Solaris 10.
I have a 1.5 TB hard drive plugged into a USB dock plugged into the Solaris machine. I ran 'cfgadm -al' and can see that the usb0/1 is usb-storage that was not there before.
How do i mount this drive and format... (3 Replies)
Hi, I've got an issue here: After I logon to the xscf prompt of this Sun M5000 and did 'XSCF> version -c xcp', the xscf prompt disappeared. I can't get it back and can't log out.
exit
rebootxscf
logout
#.
#>
#>
~#
~#
exit
sendbreak
exit
I tried to set the Mode Switch to the service... (3 Replies)
Hi,
I've configured this Sun M5000 to use two system domains (added a second domain to it). The following is the info about the settings. The showdevices command can't show devices on domain 1 because Solaris is not loaded on it yet.
My question: How can I confirm the hardware devices such as... (5 Replies)
Hi,
I would appreciate some help.
I remotely access, across a VPN, an M5000 and when I connect to the XSCF I can then access the OS using console -d0 and then I can get to the console.
The problem I have is that I need to run something which will take many hours and I can't run it in the... (6 Replies)
Hi all,
I'm developing a short program to look-up for all devices connected to the computer. Using udev and libusb libraries I achieved some progress but I can not find the way to find the mount point.
For instance, given a device that I can retrieve using libusb, I would like to know... (4 Replies)
Hi,
I'm planning to upgrade the XSCF firmware on an M5000, and have a question regarding the OBP part of the upgrade. At the moment, the system looks like this:
XCP0 (Current): 1100
OpenBoot PROM : 02.18.0000
XSCF : 01.10.0000
root@server01 # /usr/sbin/prtconf -V
OBP 4.24.15... (3 Replies)
I took over an M5000 and have a jumper server with a nic to connect to the console IP of an M5000. access via ssh user@ip.
it was working fine, another person can connect remotely on the subnet, but when I ssh,it just hangs and then times out.
so my question is,
any ideas of what I might... (4 Replies)
Discussion started by: rrodgers
4 Replies
LEARN ABOUT CENTOS
xcursorgen
XCURSORGEN(1) General Commands Manual XCURSORGEN(1)NAME
xcursorgen - create an X cursor file from a collection of PNG images
SYNOPSIS
xcursorgen [ -V ] [ --version ] [ -? ] [ --help ] [ -p dir ] [ --prefix dir ] [ config-file [ output-file ] ]
DESCRIPTION
Xcursorgen reads the config-file to find the list of cursor images along with their hotspot and nominal size information. Xcursorgen con-
verts all of the images to Xcursor format and writes them to the output-file.
Each line in the config file is of the form:
<size> <xhot> <yhot> <filename> <ms-delay>
Multiple images with the same <size> are used to create animated cursors, the <ms-delay> value on each line indicates how long each image
should be displayed before switching to the next. <ms-delay> can be elided for static cursors.
If config-file is not specified, or is specified as "-", standard input is used for the configuration file. If output-file is not speci-
fied, or is specified as "-", standard output is used for the output file.
OPTIONS -V, --version
Display the version number and exit.
-?, --help
Display the usage message and exit.
-p dir, --prefix dir
Find cursor images in the directory specified by dir. If not specified, the current directory is used.
SEE ALSO Xcursor(3)X Version 11 xcursorgen 1.0.5 XCURSORGEN(1)