07-22-2013
Quick question...what does your dladm show-phys show? Also did you ipadm ip-create the interface?
9 More Discussions You Might Find Interesting
1. Solaris
Hi,
I have a primary/slave Bind 9 setup running on a Solaris 10 platform. Everything is hunky dorey, except for when I make a zone file change and up the serial the file that is transferred to the slave looses all its comments, and the entries are place in alphabetical order.
I administer many... (1 Reply)
Discussion started by: fulhamfcboy
1 Replies
2. Solaris
Hi All ,
I try to install some packages in my global zone...
On the execution of the installion of the script it quits by saying the error
"Non global zone check failed"
Kindly help me in this regard
Thanks in advance,
jeganr (7 Replies)
Discussion started by: jegaraman
7 Replies
3. Solaris
Hi Gurus
I am not able to ping the local zone from global zone
when i am trying to ping i am getting below
ICMP Host Unreachable from gateway zone ( 192.268.35.210)
for icmp from zone ( 192.168.35.210) to sun1 ( 192.168.35.210)
However i can ping local zone from global
please... (12 Replies)
Discussion started by: kumarmani
12 Replies
4. Solaris
Hi Greetings...
I have an issue in connecting the zone from outside the network and it is because of default gateway. I can ping default gateway from inside the zone and not able to ping from global zone due to different VLAN issue. If i add two different gateways and restart network services,... (2 Replies)
Discussion started by: vvpotugunta
2 Replies
5. Solaris
I have two physical servers, with zones that mount local storage.
We were using "raw device" in the zonecfg to point to a metadevice on the global zone (it was not mounted in the global zone at any point).
It failed to mount on every boot because the directory existed in the zone.
I... (6 Replies)
Discussion started by: BG_JrAdmin
6 Replies
6. Solaris
can some one help me out as it is showing 2 different time zones in global zone and nonglobal zone .In global zone it is showing in GMT while in nonglobal zone i it showing as PDT.
System in running with solaris 10 (3 Replies)
Discussion started by: ravijanjanam12
3 Replies
7. Solaris
So this is Solaris 11.1. I have a Global zone that has several non-global zones running in it. I want to change the capped-memory.physical resources setting in ALL the zone configs of the running zones.
if I were to do this manually here's what I would do:
zonecfg -z zone1
select... (2 Replies)
Discussion started by: os2mac
2 Replies
8. UNIX for Advanced & Expert Users
Dear all,
recently, I migrated a solaris zone from one host to another. The zone was inside of a zpool. The zpool cotains two volumes.
I did the following:
host1:
$ zlogin zone1 shutdown -y -g0 -i0 #Zone status changes from running to installed
$ zpool export zone1
host2:
$ zpool... (2 Replies)
Discussion started by: custos
2 Replies
9. Solaris
Hi, hoping someone can help, its been a while since I used Solaris.
After creating a NGZ (non global zone), the NGZ can access the GZ (Global Zone) and the GZ can access the NGZ (using ssh, zlogin)
However, the NGZ cannot access any other netwqork devices, it can't even see the default router
... (2 Replies)
Discussion started by: GazinLincoln
2 Replies
LEARN ABOUT OPENSOLARIS
wpad
wpad(1M) System Administration Commands wpad(1M)
NAME
wpad - WPA and WPA2 protocol daemon
SYNOPSIS
/usr/lib/inet/wpad [-i interface] [-k pre_shared_key_name]
DESCRIPTION
The wpad daemon provides common client functionality for the WiFi Protected Access (WPA) versions 1 and 2, as defined by IEEE802.11i stan-
dard. WPA was created by the WiFi Alliance, an industry trade group. WPA implements the majority of the IEEE 802.11i standard, and was
intended as an intermediate measure to take the place of Wired Equivalent Privacy (WEP) while 802.11i was prepared. WPA2 implements the
full standard.
wpad provides the following WPA/IEEE 802.11i features:
o WPA-PSK ("WPA-Personal")
o Key management for CCMP, TKIP, WEP104, WEP40
Stop and start the wpad daemon using dladm(1M). Use:
# dladm connect-wifi
...to start the wpad daemon. Use:
# dladm disconnect-wifi
...to stop the daemon.
OPTIONS
The following options are supported:
-i interface
Specify a WiFi Link interface to start the wpad daemon.
-k pre_shared_key_name
Specify the pre-shared key used for the WiFi Link.
EXAMPLES
Example 1 Starting the wpad Daemon on Specific WiFi Link
To create the WPA key psk, enter the following command:
# dladm create-secobj -c wpa psk
To use key psk to connect to ESSID wlan on link ath0, enter the following command:
# dladm connect-wifi -k psk -e wlan ath0
Example 2 Stopping the wpad Daemon on Specific WiFi Link
To stop the daemon on the link ath0, enter:
# dladm disconnect-wifi ath0
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWwpau, SUNWwpar |
+-----------------------------+-----------------------------+
|Interface Stability |Uncommitted |
+-----------------------------+-----------------------------+
SEE ALSO
svcs(1), dladm(1M), svcadm(1M), attributes(5), smf(5)
NOTES
The wpad service is managed by the service management facility, smf(5), under the service identifier:
svc:/network/wpa:<link>
Administrative actions on this service, such as enabling, disabling, or requesting restart, can be performed using svcadm(1M). The ser-
vice's status can be queried using the svcs(1) command.
SunOS 5.11 11 Mar 2008 wpad(1M)