07-21-2013
Probably during installation these are default options, but mkfs afterwards does not set acl by default.
You can use the mount command to check if those mount options like usrquota and grpquota are active, but that will not show the default mount options. You can also set new default mount options with the tune2fs command, but these will then not show with the mount command.
9 More Discussions You Might Find Interesting
1. Solaris
Thinking of using our San for network backups..
Have a Netra 240 being installed and planning to get some space on our San.
Do you know what software is used to access the San from my server or what I would need to do? I know how to connect to local storage, disk arrays etc but not sure what... (1 Reply)
Discussion started by: frustrated1
1 Replies
2. Filesystems, Disks and Memory
Hi,
I have an existing SUN server that has a SAN storage installed on it. It also has softwares like Appwrox(scheduler), Taradata (database client), Samba Share and a few more installed on it.
Now suppose that I have a new unix server server and i switch the same SAN store from the old unix... (1 Reply)
Discussion started by: myloginid
1 Replies
3. AIX
I have 3 SAN disks of 1 TB each. Is it more efficient to make 1 large Volume group with multiple LV's or 3 Volume Groups with 1 LV each. The SAN disk is where all my backups will be dumped.:confused: (1 Reply)
Discussion started by: daveisme
1 Replies
4. Red Hat
Hello,
I am using LINUX OS. I want to check what is the SAN storage size. How do i check this in server? Any help is really appreciated.. (3 Replies)
Discussion started by: govindts
3 Replies
5. Solaris
HI all,
I had recently change the Server storage from EMC to the IBM SAN.
but after the configuration, the IBM success to see the server HBA port and successfully assign a LUN for the server.
When i go to the server, and restarted it. i use the "format" command to check, but din see any... (1 Reply)
Discussion started by: SmartAntz
1 Replies
6. UNIX for Dummies Questions & Answers
hi guys
I installed Centos 5.5 (local disk). I am using 2 HBAs
Now I mapped 5 LUNs from a Storage.
I will be using LVM
just to test I assigned a LUN I've read I have to use multipath to avoid my Centos see the LUN twice
I enabled mdmpd and multipathd...
something else I should do?
... (8 Replies)
Discussion started by: kopper
8 Replies
7. Solaris
Hi,
We are planning to setup a 10gR2 RAC and storage on ASM. We use Sun StorEdge SAN.
The installation and configuration manual says to configure ASM diskgroups with raw devices (preferably raw disk not volumes).
I dont really know if its possible to present raw disks to the Solaris... (4 Replies)
Discussion started by: esmgr
4 Replies
8. AIX
Can anyone recommend a good book on san storage basics and how it communicates with an AIX server? (1 Reply)
Discussion started by: NycUnxer
1 Replies
9. Solaris
hi all,
I am on solaris 10 1/13 and new to SAN storage.
I am required to connect to the LUNs on the SAN storage and is asked to provide the WWN information to the storage administrator.
Right now, it will be just 1 connection from a single hba port to the FCport on the storage directly,... (1 Reply)
Discussion started by: javanoob
1 Replies
LEARN ABOUT X11R4
mount.nfs
MOUNT.NFS(8) System Manager's Manual MOUNT.NFS(8)
NAME
mount.nfs, mount.nfs4 - mount a Network File System
SYNOPSIS
mount.nfs remotetarget dir [-rvVwfnsh ] [-o options]
DESCRIPTION
mount.nfs is a part of nfs(5) utilities package, which provides NFS client functionality.
mount.nfs is meant to be used by the mount(8) command for mounting NFS shares. This subcommand, however, can also be used as a standalone
command with limited functionality.
remotetarget is a server share usually in the form of servername:/path/to/share. dir is the directory on which the file system is to be
mounted.
Under Linux 2.6.32 and later kernel versions, mount.nfs can mount all NFS file system versions. Under earlier Linux kernel versions,
mount.nfs4 must be used for mounting NFSv4 file systems while mount.nfs must be used for NFSv3 and v2.
OPTIONS
-r Mount file system readonly.
-v Be verbose.
-V Print version.
-w Mount file system read-write.
-f Fake mount. Don't actually call the mount system call.
-n Do not update /etc/mtab. By default, an entry is created in /etc/mtab for every mounted file system. Use this option to skip making
an entry.
-s Tolerate sloppy mount options rather than fail.
-h Print help message.
nfsoptions
Refer to nfs(5) or mount(8) manual pages.
NOTE
For further information please refer nfs(5) and mount(8) manual pages.
FILES
/etc/fstab file system table
/etc/mtab table of mounted file systems
SEE ALSO
nfs(5), mount(8),
AUTHOR
Amit Gud <agud@redhat.com>
5 Jun 2006 MOUNT.NFS(8)