06-26-2013
Configure Second NIC on HP UX?
Hello,
I need to configure a second NIC on my HP UX, B.11.31 U ia64 ...if it is helpful.
I see a good thread to start on:
Configuring NIC
Configuring NIC
I have started reading the man pages listed. Without having to know every last detail is there a good how to guide I can follow? Also is this multicast-ing?
My end goal is normal network traffic is fine on this system, however I have gone to a tapeless backup and want every bit of speed performance I can get out of the network. TIA.
9 More Discussions You Might Find Interesting
1. Solaris
can someone please through light on how to configure video and nic.
Dimension 3000 Series, Intel Pentium 4 Processor at 2.8GHz
256MB DDR SDRAM at 400MHz EA 0.00 0.00
17 in (17 in viewable) E173FP Flat Panel Display EA
Integrated Intel Extreme Graphics 2 EA
Intel Pro 100M Integrated... (4 Replies)
Discussion started by: Jimmpy
4 Replies
2. Solaris
I wanted to configure a second NIC card on a different IP on my Sun E450 server.
Currently, I have hme0.
when I ran the command : ifconfig hme1 <ip address> netmask <subnet mask> broadcast + up
I got the following error message: ifconfig: SIOCGIFFLAGS: hme1: no such interface
Any idea... (3 Replies)
Discussion started by: Remi
3 Replies
3. SuSE
Hi all,
i tried to set up two network cards in Linux. During installation, it can detect both; eth0 and eth1. In the GUI, i can click on eth0 and type in the IP add and netmask. In the lower half of the window, I can also enter the gateway,hostname,and DNS servers
When i click on eth1, i can... (5 Replies)
Discussion started by: new2ss
5 Replies
4. Solaris
Hi , I came across a SUN server whereby it was installed with additional ethernet card. By right in any configuration, you would probably see the onboard ports Net0,Net1 and so on should correspond to e1000g0,e1000g1...
But instead the ext PCI takes precedence in the order and the Net0 becomes... (3 Replies)
Discussion started by: incredible
3 Replies
5. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
6. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
7. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
8. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
9. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
GETTABLE(8) System Manager's Manual GETTABLE(8)
NAME
gettable - get NIC format host tables from a host
SYNOPSIS
/usr/sbin/gettable [ -v ] host [ outfile ]
DESCRIPTION
Gettable is a simple program used to obtain the NIC standard host tables from a ``nicname'' server. The indicated host is queried for the
tables. The tables, if retrieved, are placed in the file outfile or by default, hosts.txt.
The -v option will get just the version number instead of the complete host table and put the output in the file outfile or by default,
hosts.ver.
Gettable operates by opening a TCP connection to the port indicated in the service specification for ``nicname''. A request is then made
for ``ALL'' names and the resultant information is placed in the output file.
Gettable is best used in conjunction with the htable(8) program which converts the NIC standard file format to that used by the network
library lookup routines.
SEE ALSO
intro(3N), htable(8), named(8)
BUGS
If the name-domain system provided network name mapping well as host name mapping, gettable would no longer be needed.
4.2 Berkeley Distribution November 17, 1996 GETTABLE(8)