06-11-2013
Are the original machines on the network, that they might create name and address collisions?
9 More Discussions You Might Find Interesting
1. Solaris
When I installed the SOLARIS 10 OS first time, the desktop would not start up, this was because of network setup. Reinstalled worked. After a week due to some problem I had to reinstall OS, installation went fine and but when i reboot I get this error.
cannot find mis/krtld
boot error loading... (0 Replies)
Discussion started by: johncy_j
0 Replies
2. UNIX for Advanced & Expert Users
Hi all... I was accidentally wipe off my iphone and lost all the data in it:(. So I tried to use dd to create an image from iphone and ssh to the Mac by using:
dd if=/dev/disk | ssh user@MacIP of='image.img'
Then I mount this image on Mac/Windows and run recovery software because most of the... (1 Reply)
Discussion started by: seraphc
1 Replies
3. Shell Programming and Scripting
Hi,
I would like to learn shell scripting in UNIX. Can any one please give me the support and share the information/documents with me.
If any documents please post it to aswanikumar_nimmagadda@yahoo.co.in
Thanks in advance...!!! (3 Replies)
Discussion started by: aswani_n
3 Replies
4. UNIX for Dummies Questions & Answers
Hi,
Does anyone know how to make BASH provide a list of possible completions on the first tab, and then start cycling through the possibilites on the next tab?
Right now this is what I have in my .bashrc:
bind "set show-all-if-ambiguous on"
bind \\C-o:menu-complete
This allows... (0 Replies)
Discussion started by: Mithu
0 Replies
5. UNIX for Advanced & Expert Users
Hi Folks
I have been debugging a script that is called every thirty seconds. Basically it is doing a ps, well two actually, one to file (read by the getline below) and the other into a pipe. The one into the pipe is: -
V_SYSVPS=/usr/sysv/bin/ps
$V_SYSVPS -p$PIDLIST -o$PSARGS... (0 Replies)
Discussion started by: steadyonabix
0 Replies
6. Shell Programming and Scripting
Hi
I have written a script .The script runs properly if i write sql queries .But if i use PLSQL commands of BEGIN if end if , end ,then on running the script the comamds are getting printed on the prompt .
Ex :temp.sql
After connecting to the databse at the sql prompt i type... (1 Reply)
Discussion started by: isha_1
1 Replies
7. Boot Loaders
Hello,
I have kubuntu on my laptop and now I decided to switch to Windows 7. I made the bios settings properly (first choice is boot from cd\vd) but I see the error
" reboot and select proper Boot device or insert Boot media in select Boot device and press a key "
I have tried CD and... (0 Replies)
Discussion started by: rpf
0 Replies
8. HP-UX
Hello,
I have a very old hp rp2450 running 11i2 that I had to power off. When turning it back on it hangs with the following message. Would booting into SUM get me any further? I've never used SUM, so I'm asking before I go down that rabbit hole.
Thanks for the help.
#
## extra content... (1 Reply)
Discussion started by: calabaria
1 Replies
9. Programming
among the below socket programming api's, please let me know which are blocking and non-blocking.
socket
accept
bind
listen
write
read
close (2 Replies)
Discussion started by: VSSajjan
2 Replies
LO(4) BSD Kernel Interfaces Manual LO(4)
NAME
lo -- software loopback network interface
SYNOPSIS
pseudo-device loop
DESCRIPTION
The loop interface is a software loopback mechanism which may be used for performance analysis, software testing, and/or local communication.
As with other network interfaces, the loopback interface must have network addresses assigned for each address family with which it is to be
used. These addresses may be set or changed with the SIOCSIFADDR ioctl(2). The loopback interface should be the last interface configured,
as protocols may use the order of configuration as an indication of priority. The loopback should never be configured first unless no hard-
ware interfaces exist.
The loopback interface lo0 is created at boottime, it always exists and cannot be destroyed with ifconfig(8). Additional loopback interfaces
can be created by using the ifconfig(8) create command.
DIAGNOSTICS
lo%d: can't handle af%d . The interface was handed a message with addresses formatted in an unsuitable address family; the packet was
dropped.
SEE ALSO
inet(4), intro(4), ifconfig(8)
HISTORY
The lo device appeared in 4.2BSD.
BUGS
Previous versions of the system enabled the loopback interface automatically, using a nonstandard Internet address (127.1). Use of that
address is now discouraged; a reserved host address for the local network should be used instead.
BSD
September 3, 2006 BSD