Hi all,
I have a problem with vxvm volume which is mirror with two disks. when i am try to increase file system, it is throwing an ERROR: can not allocate 5083938 blocks, ERROR: can not able to run vxassist on this volume.
Please find a sutable solutions.
Thanks and Regards
B. Nageswar... (0 Replies)
Hi,
Is there are any special preocedure for extending veritas mirror-stripe volume? In my case , volume lay out looks as below
v test - ENABLED ACTIVE 419430400 SELECT - fsgen
pl test-01 test ENABLED ACTIVE 419454720 STRIPE 3/128 RW
sd... (0 Replies)
I've looked a little but haven't found a solid answer, assuming there is one.
What's better, hardware mirroring or ZFS mirroring? Common practice for us was to use the raid controllers on the Sun x86 servers. Now we've been using ZFS mirroring since U6. Any performance difference? Any other... (3 Replies)
Hi ,
I am new to SVM .when i try to learn RAID 1 , first they are creating two RAID 0 strips through
metainit d51 1 1 c0t0d0s2
metainit d52 1 1 c1t0d0s2
In the next step
metainit d50 -m d51
d50: Mirror is setup
next step is
metaattach d50 d52
d50 : submirror d52 is... (7 Replies)
I have a machine (5.10 Generic_142900-03 sun4u sparc SUNW,Sun-Fire-V210) that we are upgrading the storage and my task is to mirror what is already on the machine to the new disk. I have the disk, it is labeled and ready but I am not sure of the next steps to mirror the existing diskgroup and... (1 Reply)
Hi All,
We are using Solaris 10 x86, and Veritas Storage Foundation Software version 6.0.1 and faced the following issues after mirroring and during boot from mirror.
1) VTOC has been changed after mirroring the rootdisk with this command - " /opt/VRTS/bin/vxrootmir <disk to be mirrored>".... (0 Replies)
I have modified a script to do a circular DNS look up.
The theory is this
for a given subnet build a range if IP's
do a reverse look up on those IP's
take the output of the reverse look up then and do a forward look up
If the returns match up give a good status
If not return a fail... (1 Reply)
Hi Experts,
I wanted to extend a veritas file system which is running on veritas cluster and mounted on node2 system.
#hastatus -sum
-- System State Frozen
A node1 running 0
A node2 running 0
-- Group State
-- Group System Probed ... (1 Reply)
Hi
I write below script to show if expected file exist in /etc/library/ , print success else failed. But it will print full path I just need to print module name in output. And if it possible show time that spent to compile each module.
FYI 1: First run another script just go to the paths... (1 Reply)
Discussion started by: indeed_1
1 Replies
LEARN ABOUT DEBIAN
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)