Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Networking Issue (Cant Ping the gateway)
Operating Systems AIX Networking Issue (Cant Ping the gateway) Post 302814411 by MichaelFelt on Wednesday 29th of May 2013 11:44:50 AM
Old 05-29-2013
From the command line:

# route add -net default A.B.C.D

However, the chdev command above is better (smitty netstat) because these put it in the ODM and it is permanent.

However, if you cannot ping the gw, adding it will not help any.

1) can the VIOS ping the gw?
2) can you ping the VIOS?

if the answer to 1) is yes, and 2) is no you probably do not have the SEA setup yet.

if the answer to both is yes - I still suspect something wrong with the virtual ethernet setup.

Are there other partitons? Can they ping the gw? Can you ping the other partitions?
This User Gave Thanks to MichaelFelt For This Post:
pjeedu2247
 

10 More Discussions You Might Find Interesting

1. IP Networking

Unable to ping the gateway IP itself

We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command 64 bytes from 124.168.215.40:... (6 Replies)
Discussion started by: chrisanto_2000
6 Replies

2. IP Networking

ping and networking

Dear friends, Please explain the functionality of the ping command and explain the network details, and IP layers. I want some more clarification about following things i) switch ii) hub iii) routers iv) proxy (3 Replies)
Discussion started by: thangappan
3 Replies

3. IP Networking

Multihomed can not ping gateway

Hello this is my first post at this forum. Apologize for my lack of network understanding but Im posting to learn. I have a problem reaching default gateway 10.18.110.1 If I use my laptop I can ping 10.18.110.1 but with our red hat multihomed server the gateway does not respond to ping. cat... (11 Replies)
Discussion started by: vettec3
11 Replies

4. Solaris

ping -s to default gateway very slow

I was install new solaris10 on m4000 model after that i "ping -s" to default gateway but it's take longtime (2 Min) to reply and if i use "ping" only it's reply to fase(2 sec). any body who can tell me about my problem and how to fix it please. i'm try to fix several days. (2 Replies)
Discussion started by: cesmk
2 Replies

5. AIX

Can not Ping Gateway

Hello, I am new to Unix :D and have been trying to configure an AIX server running 5.3. I used smitty or smit to configure interface 0 on the server. I am able to ping the IP I set, however I am still unable to ping the gateway. I configured the IP by navigating to Communications Applications... (6 Replies)
Discussion started by: cdub50
6 Replies

6. Red Hat

Cannot ping gateway

I know the subject line is very similar to: destination host unreachable but the problem with my machine appears to be somewhat different from that thread. apologies if I missed something from there. We recently moved a machine physically and from one subnet to another . I used... (1 Reply)
Discussion started by: mirage
1 Replies

7. UNIX for Dummies Questions & Answers

Cannot ping default gateway

I have NCR MP-RAS unix. I have been trying for several months to get our network working since we had never used it before. I have setup all routes that I can think of. I know it has something to do with the routing table, because out of sheer luck I was able to get it working, and than like a... (4 Replies)
Discussion started by: Rutgerncas
4 Replies

8. AIX

LPAR Networking: Can't ping

So I have created an LPAR. I think I have configured everything properly but I can't ping the network. The LPAR is on a VLAN. Other LPARs on the same VLAN works. Here's some info on the LPAR: # entstat -d ent1 -------------------------------------------------- ETERNET STATISTICS (en1) :... (20 Replies)
Discussion started by: PPPP
20 Replies

9. Red Hat

Can not ping default gateway

Hi, Here is the issue: There are 2 identical systems in the same subnet here. They can ping and ssh each other. One can ping the default gateway and one can not with error '... icmp_seq Destination Host Unreachable'. I can't find any difference between the two systems in terms of network... (4 Replies)
Discussion started by: aixlover
4 Replies

10. UNIX for Advanced & Expert Users

Unable to ping default gateway

I have setup a Linux machine on my server but for some reason Im unable to reach my default gateway. This is causing me to not communicate with the outside world (unable to connect to CentOS repos) # ifconfig enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet... (3 Replies)
Discussion started by: Junaid Subhani
3 Replies

LEARN ABOUT SUNOS

jms-ping

asadmin-jms-ping(1AS)						   User Commands					     asadmin-jms-ping(1AS)

NAME

       jms-ping  - checks to see if the JMS provider is up and running

SYNOPSIS

       jms-ping   --user  admin_user  [--password  admin_password]  [--host  localhost]  [--port  4848]  [--passwordfile  filename]  [--secure|-s]
       [--terse=false] [--echo=false] [--interactive=false]

       Checks to see if the JMS provider is up and running. This command is supported in remote mode only.

OPTIONS

       --user		       authorized domain application server administrative username.

       --password	       password to administer the domain application server.

       --host		       machine name where the domain application server is running.

       --port		       port number of the domain application server listening for administration requests.

       --passwordfile	       file containing the domain application server password.

       --secure 	       if true, uses SSL/TLS to communicate with the domain application server.

       --terse		       indicates that any output data must be very concise, typically avoiding human-friendly sentences and favoring well-
			       formatted data for consumption by a script. Default is false.

       --echo		       setting to true will echo the command line statement on the standard output. Default is false.

       --interactive	       if set to true (default), only the required password options are prompted.

       Example 1: Using jms-ping

       asadmin> jms-ping --user admin --password adminadmin --host bluestar --port 4848 server1
       JMS Ping Status=RUNNING

EXIT STATUS

       0		       command executed successfully

       1		       error in executing the command

       asadmin-create-jmsdest(1AS), asadmin-delete-jmsdest(1AS), asadmin-list-jmsdest(1AS)

J2EE 1.4 SDK							    March 2004						     asadmin-jms-ping(1AS)
All times are GMT -4. The time now is 11:00 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy