I prefer snmp. I do not have the proper perl modules loaded on the platorm. Snmp isnt loaded on the platform. Telnet is not an option. I need to write an expect script to pull cisco equipment configs.
The following code is executed once I gain access.
the running config is large.
This Expect script provides expect with a list of IP addresses to Cisco IPS sensors and commands to configure Cisco IPS sensors. The user, password, IP addresses, prompt regex, etc. have been anonymized. In general this script will log into the sensors and send commands successfully but there are... (1 Reply)
Hi everyone :),
I need sort Cisco configs to report but i cannot do the script to made this:
#### INPUT #####
config-register 0x2102
version 12.2
!
hostname Router
!
interface Ethernet0
description Red LAN
ip address 192.168.1.1 255.255.255.0
no cdp enable
!
interface Serial0... (6 Replies)
At times I find the need to test that the tacacs port 49 is open.
The code below works but is painfully slow because I have to wait on the timeouts.
Examples of possible responds
router1#telnet 10.11.20.14 49
Trying 206.112.204.140, 49 ... Open
route1#telnet 10.11.19.14 49
Trying... (1 Reply)
Hey everyone,
I have a few question.
1. Is it possible to display cisco 'show run' output command to the application ??
2. And is there any ways to log in to the router instead of using telnet from telnet application???
Thanks in advance (0 Replies)
Hi all,
I use a bash script which use expect to connect throught ssh and run command on a cisco router. The ssh connection with expect work fine, but the first command on the cisco router failed,
I try to run the command in error by hand and it work fine... :(
the first part of the script... (2 Replies)
Ladies & Gents,
Can one of you gurus please show me a very simple "expect" script to change the password in Solaris in a script, please? Nothing fancy, no error checking, no nothing. Just to change the password of a new user, it's all.
Many thanks in advance. U guys have honestly earned my... (1 Reply)
HI all
i need to connect to about 900 cisco routers and switch to do some configs changes. the issue i am having is that half the devices have one set of username and password and the other half have another username and password. From expect or bash script i can ssh into a device and make... (0 Replies)
Discussion started by: quintin
0 Replies
LEARN ABOUT MOJAVE
platform::shell
platform::shell(n) Tcl Bundled Packages platform::shell(n)
__________________________________________________________________________________________________________________________________________________NAME
platform::shell - System identification support code and utilities
SYNOPSIS
package require platform::shell ?1.1.4?
platform::shell::generic shell
platform::shell::identify shell
platform::shell::platform shell
_________________________________________________________________DESCRIPTION
The platform::shell package provides several utility commands useful for the identification of the architecture of a specific Tcl shell.
This package allows the identification of the architecture of a specific Tcl shell different from the shell running the package. The only
requirement is that the other shell (identified by its path), is actually executable on the current machine.
While for most platform this means that the architecture of the interrogated shell is identical to the architecture of the running shell
this is not generally true. A counter example are all platforms which have 32 and 64 bit variants and where a 64bit system is able to run
32bit code. For these running and interrogated shell may have different 32/64 bit settings and thus different identifiers.
For applications like a code repository it is important to identify the architecture of the shell which will actually run the installed
packages, versus the architecture of the shell running the repository software.
COMMANDS
platform::shell::identify shell
This command does the same identification as platform::identify, for the specified Tcl shell, in contrast to the running shell.
platform::shell::generic shell
This command does the same identification as platform::generic, for the specified Tcl shell, in contrast to the running shell.
platform::shell::platform shell
This command returns the contents of tcl_platform(platform) for the specified Tcl shell.
KEYWORDS
operating system, cpu architecture, platform, architecture
platform::shell 1.1.4 platform::shell(n)