Check and verify if you have any control characters in your file:
Also set xtrace / verbose and debug your script to understand what is causing this error:
Hi,
There is a file having a list of running PIDs and another file having
a list of registered PIDs. How can we check if each value of running
PIDs are less or more than the registered PIDs i.e. comparing the
value of each PID in both the files.
Request you to pls give your inputs. ... (2 Replies)
Hello all
while writing a small script , i got stuck with this simple thing.Hope you guyz can help.
Iam trying to read password
echo"enter password"
read $pwd
now i have to check this
echo"enter password to proceed"
read $pwd
now i have to check both the values of the... (2 Replies)
Hi all,
I have got a problem while comparing 2 text files and the result should contains the unique values(Non repeatable).
For eg:
file1.txt
1
2
3
4
file2.txt
2
3
So after comaping the above 2 files I should get only 1 and 4 as the output. Pls help me out. (7 Replies)
i have two file and i am comparing both..
in cmp1 ,the content is :
the nu of file is : <some integer value>
in cmp2 ,the content is :
the nu of file is :
so want a script which will take value (2) when cmp1 is compared with cmp2..
i mean cmp cmp1 cmp2 the the output will be
he nu of... (1 Reply)
Hi to all,
I have the following text within inputfile
data1,value1,value2
data1,value3,value2
data1,value5,value6
data2,value1,value2
data2,value3,value4
data3,value1,value2
data3,value3,value4
data4,value1,value2
data4,value3,value4
data4,value5,value6
I would like to... (4 Replies)
Hi all,
I am new to unix and I am trying hard to get this requirement, but no luck.
I am trying to compare two cloumns in two files and if it matches, the last column in file1 must be divided by file2 and the output must be written in a new file. To elaborate the 2nd column in file1 (EUR) must be... (6 Replies)
I have two text files where the first three columns are exactly the same. I want to compare the fourth column of the text files and if the values are different, print that row into a new output file. How do I go about doing that?
File 1:
100 rs3794811 0.01 0.3434
100 rs8066551 0.01... (8 Replies)
Hi,
I have two text files with matching first columns. Some of the values in the second column do not match. I want to write a script to print out the rows (only the first column) where the values in the second column do not match.
Example:
Input 1
A 1
B 2
C 3
D 4
Input 2
A 2
B 2... (6 Replies)
First I'd like to apologize if I opened a thread which is already open somewhere.
I did a bit of searching but could quite find what I was looking for, so I will try to explaing what I need.
I'm writing a script on our server, got to a point where I have two files with results. Example:
File1... (6 Replies)
I was trying to extract value of g1 and p1 only inside the tags where t1 is "Reading C (bytes)" and comparing them to make sure p1 is always less than g1. Here is the Json file I'm using -
File:-
{
"g1" : 1482568,
"n1" : "v_4",
"p1" : 0,
"s1" : "RC",
"t1" : "LM",
}
{
"g1" :... (3 Replies)
Discussion started by: Mannu2525
3 Replies
LEARN ABOUT DEBIAN
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)