:mad: I did this the other day but one of my support personnel removed my history so i could call it back up to remeber the exact command since i am air-headed at times. I am trying to take a 30 MEG file off the system and drop it to tape then i want to make the file go back to being 0 bytes so... (1 Reply)
I'm doing a bit of hex editing with dd and I can replace values fairly simply. However, I've run across a situation where I need to delete bytes in the file and I'm not sure how to do that. For example:
Input file has:
1234567890
Output needs to be:
123abc90
I tried this:
printf... (6 Replies)
Hi all,
Does anybody know or guide me on how to remove the first N bytes and the last N bytes from a binary file? Is there any AWK or SED or any command that I can use to achieve this?
Your help is greatly appreciated!!
Best Regards,
Naveen. (1 Reply)
What is the easiest way to inspect the bytes stored in a file?
Ideally, If my file was 10 bytes each of which had only the high bit set, I'd be able to browse for it and get output like this:
01 - 10000000
02 - 10000000
03 - 10000000
04 - 10000000
05 - 10000000
06 - 10000000
07 -... (7 Replies)
Hi Guyz,
I need to capture first N Bytes from the first line of my file.
Eg. If i have following data in File1
414d51204541495052475731202020204a910846230e420c Hello 3621363663212 Help Required
Then, i want the value of first 48 Bytes to be stored in a variable.
That is, variable... (5 Replies)
While running script I am getting an error like
Few lines in data are not being processed.
After googling it I came to know that adding such line would give some memory to it
ini_set("memory_limit","64M");
my input file size is 1 GB.
Is that memory limit is based on RAM we have on... (1 Reply)
Hi,
If I want to copy a 1024 byte data stream in to the target location in 3-bytes chunk, I guess I can use the following script.
dd bs=1024 count=3 if=/src of=/dest
But, I would like to know, how to do it via a C program. I have tried this with memcpy(), that did not help. (3 Replies)
Hello guys. I really hope someone will help me with this one..
So, I have to write this script who:
- creates a file home/student/vmdisk of 10 mb
- formats that file to ext3
- mounts that partition to /mnt/partition
- creates a file /mnt/partition/data. In this file, there will... (1 Reply)
hello,
suppose, entered input is of 1-40 bytes, i need it to be converted to 40 bytes exactly.
example: if i have entered my name anywhere between 1-40 i want it to be stored with 40 bytes exactly.
enter your name:
donald duck (this is of 11 bytes)
expected is as below - display 11... (3 Replies)
Discussion started by: shravan.300
3 Replies
LEARN ABOUT MINIX
ppmtosixel
ppmtosixel(1) General Commands Manual ppmtosixel(1)NAME
ppmtosixel - convert a portable pixmap into DEC sixel format
SYNOPSIS
ppmtosixel [-raw] [-margin] [ppmfile]
DESCRIPTION
Reads a portable pixmap as input. Produces sixel commands (SIX) as output. The output is formatted for color printing, e.g. for a DEC
LJ250 color inkjet printer.
If RGB values from the PPM file do not have maxval=100, the RGB values are rescaled. A printer control header and a color assignment table
begin the SIX file. Image data is written in a compressed format by default. A printer control footer ends the image file.
OPTIONS -raw If specified, each pixel will be explicitly described in the image file. If -raw is not specified, output will default to com-
pressed format in which identical adjacent pixels are replaced by "repeat pixel" commands. A raw file is often an order of magni-
tude larger than a compressed file and prints much slower.
-margin
If -margin is not specified, the image will be start at the left margin (of the window, paper, or whatever). If -margin is speci-
fied, a 1.5 inch left margin will offset the image.
PRINTING
Generally, sixel files must reach the printer unfiltered. Use the lpr -x option or cat filename > /dev/tty0?.
BUGS
Upon rescaling, truncation of the least significant bits of RGB values may result in poor color conversion. If the original PPM maxval was
greater than 100, rescaling also reduces the image depth. While the actual RGB values from the ppm file are more or less retained, the
color palette of the LJ250 may not match the colors on your screen. This seems to be a printer limitation.
SEE ALSO ppm(5)AUTHOR
Copyright (C) 1991 by Rick Vinci.
26 April 1991 ppmtosixel(1)