Try running the command from within /usr/xpg4/bin/sh instead of /bin/sh. The classic Bourne shell on Solaris can be a bit funny with redirects sometimes...
--
Otherwise, is there a difference without a shell redirect? for example:
or
Last edited by Scrutinizer; 05-09-2013 at 01:15 PM..
Hi All,
Can anyone explain me the meanning of the following errors:
LABEL: SC_DISK_ERR2
IDENTIFIER: B6267342
Description
DISK OPERATION ERROR
Probable Causes
DASD DEVICE
Failure Causes
DISK DRIVE
DISK DRIVE ELECTRONICS
Recommended Actions
PERFORM PROBLEM DETERMINATION... (1 Reply)
Hello experts.
I am using Solaris 10(2005) on intel machine. I have installed Veritas Volume manager 5.0. I am unable to bring a disk error to online state. I would like to bring that disk to CDS format.
Commands i used and output are....
#vxdisk list
DEVICE TYPE ... (11 Replies)
Hi all,
My disk space is 100% full.
df -k <dir> -> 100%
One of my debug files consume huge amount of space and i want to remove the same to start off fresh debugs.
However i'm unable to remove the file giving out the following error message:
rm -f debug.out22621
rm: cannot remove... (8 Replies)
one of my servers / was full by 100% i cleard some space, now though i have
enough space on / partition still df is showing disk usage as 100% am not able to create any single txt file ? why so ? (3 Replies)
I have a weird situation in which the binary dumps core and gives bus error. But before dumping the core and throwing the buss error, it gives some output.
unfortunately I can't grep the output before core dump
db2bfd -b test.bnd
maxSect 15
Bus Error (core dumped)
But if I do ... (4 Replies)
Hi,
I am unable to get the full FS space, as /home is 100% utilized and after deleting unwanted files, its still 100%. After checking the du -sk * | sort -n output and converting it to MBs, the total sizes comes out to be 351 MBs only however the lvol is of 3GB. I don't know where is all the space... (2 Replies)
i want to create 1 script to monitor 1 particular filesystem out of the diferent filesystems. if disk space of that particular filesystem increases by 80% it sends an alert mail to an email id
---------- Post updated at 04:18 PM ---------- Previous update was at 04:17 PM ----------
no. I am... (1 Reply)
Discussion started by: rakeshhhhhhhh
1 Replies
LEARN ABOUT OSF1
volreattach
volreattach(8) System Manager's Manual volreattach(8)NAME
volreattach - Reattaches disk drives that have once again become accessible
SYNOPSIS
/usr/sbin/volreattach [-rb] [accessname...]
/usr/sbin/volreattach -c accessname
OPTIONS
The volreattach utility has the following options: Calls the volrecover utility to attempt to recover stale plexes of any volumes on the
failed disk. Performs the reattach operation in the background. Checks whether a reattach is possible. No operation is performed, but the
name of the disk group and disk media name at which the disk can be reattached is displayed.
DESCRIPTION
The volreattach utility attempts to reattach disks using the same disk group and media names they had before detachment.
This operation may be necessary if a disk has a transient failure, or if some disk drivers are unloaded or unloadable when the Logical
Storage Manager is started, causing disks to enter the failed state.
If the problem is fixed, the volreattach command can be used to reattach the disks without plexes being flagged as stale, as long as the
reattach happens before any volumes on the disk are started.
The volreattach command is called from the voldiskadm menus as part of disk recovery.
The volreattach utility tries to find a disk with a disk group and disk ID matching that of the disk(s) being reattached. If the matching
disk is found, the reattach operation may still fail if the original cause (or some other cause) for the disk failure still exists.
EXIT CODES
A zero exit status is returned if it is possible to perform a reattach. Otherwise, non-zero is returned.
SEE ALSO volintro(8), voldiskadm(8), volrecover(8)volreattach(8)