Hi All,
Can anyone explain me the meanning of the following errors:
LABEL: SC_DISK_ERR2
IDENTIFIER: B6267342
Description
DISK OPERATION ERROR
Probable Causes
DASD DEVICE
Failure Causes
DISK DRIVE
DISK DRIVE ELECTRONICS
Recommended Actions
PERFORM PROBLEM DETERMINATION... (1 Reply)
Hello experts.
I am using Solaris 10(2005) on intel machine. I have installed Veritas Volume manager 5.0. I am unable to bring a disk error to online state. I would like to bring that disk to CDS format.
Commands i used and output are....
#vxdisk list
DEVICE TYPE ... (11 Replies)
Hi all,
My disk space is 100% full.
df -k <dir> -> 100%
One of my debug files consume huge amount of space and i want to remove the same to start off fresh debugs.
However i'm unable to remove the file giving out the following error message:
rm -f debug.out22621
rm: cannot remove... (8 Replies)
one of my servers / was full by 100% i cleard some space, now though i have
enough space on / partition still df is showing disk usage as 100% am not able to create any single txt file ? why so ? (3 Replies)
I have a weird situation in which the binary dumps core and gives bus error. But before dumping the core and throwing the buss error, it gives some output.
unfortunately I can't grep the output before core dump
db2bfd -b test.bnd
maxSect 15
Bus Error (core dumped)
But if I do ... (4 Replies)
Hi,
I am unable to get the full FS space, as /home is 100% utilized and after deleting unwanted files, its still 100%. After checking the du -sk * | sort -n output and converting it to MBs, the total sizes comes out to be 351 MBs only however the lvol is of 3GB. I don't know where is all the space... (2 Replies)
i want to create 1 script to monitor 1 particular filesystem out of the diferent filesystems. if disk space of that particular filesystem increases by 80% it sends an alert mail to an email id
---------- Post updated at 04:18 PM ---------- Previous update was at 04:17 PM ----------
no. I am... (1 Reply)
Discussion started by: rakeshhhhhhhh
1 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)