Hello, every one,
I tried to install redhat linux enterprise server version 4 (ES4) on the my system with the
following configuration
Pentium core 2 duo 2.66 E 6750
Intel DG33FB motherboard
160Gb Segate hard disk (SATA)
1024 mb (1GB) DDR2 TRAN RAM
Lg DVD/Cd WR
BUT AM GETTING... (0 Replies)
Dear Sir,
I am Shidlingayya India, i am new to unix script..my problem is
present-> I have to read the eeprom locations from 0 to 255 locations in separate file..i wrote the code for this as follows
@eep_save_all ;<filename> store eeprom data to intel hex file
kr 0,,02/n
wf %1,... (0 Replies)
Hi: I was setting up a modem on an Ultra5 running 2.6. (yes I know, how quaint)
There are 15 systems that are interlinked but not accessible to the outside world.
This will end soon with new updated sun systems but until then the system needs to be accessed by the outside world. Hence the... (1 Reply)
hello
i have sun machine and i need to reset EEPROM password where evrytime machine boot i should put password to start in booting
any one can help me how i can remove this password
Thanks (1 Reply)
Hi all,
So I have a binary file and I need to generate an expected EEPROM checksum for it. Ideally, I would like to input the file (with the path) and output a computed checksum. Ive been using (cksum file1) with no avail and I was just curious as to whether there is such thing as EEPROM... (1 Reply)
Hi all,
So I have a binary file and I need to generate an expected EEPROM checksum for it. Ideally, I would like to input the file (with the path) and output a computed checksum. Ive been using (cksum file1) with no avail and I was just curious as to whether there is such thing as EEPROM cksum,... (1 Reply)
I have a weird situation in which the binary dumps core and gives bus error. But before dumping the core and throwing the buss error, it gives some output.
unfortunately I can't grep the output before core dump
db2bfd -b test.bnd
maxSect 15
Bus Error (core dumped)
But if I do ... (4 Replies)
Hello all,
I am currently trying to find a solution to replacing some 10 year old Solaris boxes because it is obvious that they are going to fail soon. The problem is that they are license servers, and I need the eeprom serial to transfer to a new computer. Now, I could request that we get new... (1 Reply)
Discussion started by: DeanCarlo
1 Replies
LEARN ABOUT XFREE86
pcitweak
PCITWEAK(1) General Commands Manual PCITWEAK(1)NAME
pcitweak - read/write PCI config space
SYNOPSIS
pcitweak -l
pcitweak -r PCI-ID [-b|-h] offset
pcitweak -w PCI-ID [-b|-h] offset value
DESCRIPTION
Pcitweak is a utility that can be used to examine or change registers in the PCI configuration space. On most platforms pcitweak can only
be run by the root user.
OPTIONS -l Probe the PCI buses and print a line for each detected device. Each line contains the bus location (bus:device:function), chip
vendor/device, card (subsystem) vendor/card, revision, class and header type. All values printed are in hexadecimal.
-r PCI-ID
Read the PCI configuration space register at offset for the PCI device at bus location PCI-ID. PCI-ID should be given in the form
bus:device:function, with each value in hexadecimal. By default, a 32-bit register is read.
-w PCI-ID
Write value to the PCI configuration space register at offset for the PCI device at bus location PCI-ID. PCI-ID should be given in
the form bus:device:function, with each value in hexadecimal. By default, a 32-bit register is written.
-b Read or write an 8-bit value (byte).
-h Read or write a 16-bit value (halfword).
SEE ALSO scanpci(1)AUTHORS
David Dawes (dawes@xfree86.org).
XFree86 Version 4.7.0 PCITWEAK(1)