Thanks Rudi & Scrutinzer for the inputs. Reiterating my requirement once again as follows:
1. Input is from tar file named samplefile.tar.gz, so used following code
2. Dont want to untar the above file so used zcat.
3. Check the fields at 26th location for "01" from the tar file , so used following code
4. Also check the first character of 28th field, so used following code
5. Also check for 184th location for 3 bytes in BB array from bb.txt file, so used following code
Output required is to print all the lines from input (tar file) which is not matching the above conditions
How can I find which version of Awk is installed? OpSystem is HPUX 11.x
I am getting an error when trying to use the keyword nextfile and I dont know why! (Well, I can only assume that I have am using a version of Awk that does not support nextfile. However, according to O'Reilly, nextfile is... (3 Replies)
Hi all
I have more than 1000 files in a folder and when ever i use a "compress" or "zcat" command it give error
/bin/zcat: Arg list too long. .
any solution for this :o (3 Replies)
Hi
I am trying to extract a <filename>.tar.Z on a SLES machine using zcat.
The command I am using is
zcat <filename>.tar.Z | tar xf -
When I use the above I get the following message
tar: Read 7168 bytes from -
I think the message is benign because I see that my files where... (2 Replies)
Hi,
Putting across a few awk expressions.
Apart from the last, all of them are working.
echo a/b/c | awk -F'/b/c$' '{print $1}'
a
echo a/b/c++ | awk -F'/b/c++' '{print $1}'
a
echo a/b/c++ | awk -F'/b/c++$' '{print $1}'
a/b/c++
Request thoughts on why putting a '$' post double ++... (12 Replies)
I created a backup script that emails all the admins when the backup is complete and attaches a log file of what what backed up. On occasion, something happens in which the backups stop working, I started "grep"ing around /var/log/syslog and I usually find the smoking gun. My goal is to zcat... (8 Replies)
Hi,
just i would like to know, how will be the response if you try to read a 40GB compressed file using zcat.
a)Uncompress the 40GB file and have it in the disk. use cat to view the steps.
b)Use zcat directly to view the compressed file?
What are the steps being occurred in step (b)?
Where... (3 Replies)
Hi Guru's.
I am trying to use to check if $5 is greater than 80 & if not 100, then to print $0 :
awk '{ if ($5>80) && if ($5 != 100) print $0}
But getting error:
>bdf1|sed 's/%//g'|awk '{ if ($5>80) && if ($5 != 100) print $0}'
syntax error The source line is 1.
The error... (6 Replies)
Hello,
When i lauches this command
ssh -n server_name gunzip -c "/REP/xxxx.gz" > server.logThere are a few stray characters like NULNULNULNUL100644 NUL000000NUL000000NUL00024002704 12135060747 012607NUL at the beginning of server.log.
In the xxxx.gz there is a tar file
I'm not sure but it... (5 Replies)
I have recently built a new server and patched Soalris 10 up tp latest bundle etc...
When I run a decompress using the format zcat fred.Z |tar -xvf - it runs at a very slow rate.
A similiar server which is less powerful runs over twice as quick.
Is there any work arounds to configure decompress... (4 Replies)
Discussion started by: smcart
4 Replies
LEARN ABOUT DEBIAN
bup-margin
bup-margin(1) General Commands Manual bup-margin(1)NAME
bup-margin - figure out your deduplication safety margin
SYNOPSIS
bup margin [options...]
DESCRIPTION
bup margin iterates through all objects in your bup repository, calculating the largest number of prefix bits shared between any two
entries. This number, n, identifies the longest subset of SHA-1 you could use and still encounter a collision between your object ids.
For example, one system that was tested had a collection of 11 million objects (70 GB), and bup margin returned 45. That means a 46-bit
hash would be sufficient to avoid all collisions among that set of objects; each object in that repository could be uniquely identified by
its first 46 bits.
The number of bits needed seems to increase by about 1 or 2 for every doubling of the number of objects. Since SHA-1 hashes have 160 bits,
that leaves 115 bits of margin. Of course, because SHA-1 hashes are essentially random, it's theoretically possible to use many more bits
with far fewer objects.
If you're paranoid about the possibility of SHA-1 collisions, you can monitor your repository by running bup margin occasionally to see if
you're getting dangerously close to 160 bits.
OPTIONS --predict
Guess the offset into each index file where a particular object will appear, and report the maximum deviation of the correct answer
from the guess. This is potentially useful for tuning an interpolation search algorithm.
--ignore-midx
don't use .midx files, use only .idx files. This is only really useful when used with --predict.
EXAMPLE
$ bup margin
Reading indexes: 100.00% (1612581/1612581), done.
40
40 matching prefix bits
1.94 bits per doubling
120 bits (61.86 doublings) remaining
4.19338e+18 times larger is possible
Everyone on earth could have 625878182 data sets
like yours, all in one repository, and we would
expect 1 object collision.
$ bup margin --predict
PackIdxList: using 1 index.
Reading indexes: 100.00% (1612581/1612581), done.
915 of 1612581 (0.057%)
SEE ALSO bup-midx(1), bup-save(1)BUP
Part of the bup(1) suite.
AUTHORS
Avery Pennarun <apenwarr@gmail.com>.
Bup unknown-bup-margin(1)