04-12-2013
Thanks Rudic, but actually the devices are all identified , needed to init them. what i mean was i needed the following:
/etc/init.d/raw start;
i got this info after a lot of googling and it has worked for me,
..
i knew it would be some command only but me not having lot of exposure to UNIX untill now, found it a bit difficult. Anyways, thanks.
8 More Discussions You Might Find Interesting
1. AIX
Hy
I have several logical volumes that are turned into raw devices used by Informix DB. I would like to add some more.
In /dev directory i see logical volumes as block files: lv_name1, lv_name2 ...
and
i see raw devices defined as character files:
rlv_name1, rlv_name2 ...
As i see,... (5 Replies)
Discussion started by: veccinho
5 Replies
2. UNIX for Advanced & Expert Users
Hello group,
Is it possible to use partition on a disk as a raw device? I have a LUN on a SAN which I would like to partition and use those partitions as raw device.
If it is feasable, how do I bind them to a device?
For example, say sdd has 3 partitions on it, sdd1, sdd2 and sdd3. Can I... (1 Reply)
Discussion started by: bfay
1 Replies
3. Solaris
Hi All ,
I would like to know the procedure for increasing shared volume space in sun cluster .
Currently the configuration is like these .
Main stripe
oradb1/d91 2 1 /dev/did/rdsk/d35s0 1 /dev/did/rdsk/d36s0 =Total 49 Gb
oradb1/d94 -p oradb1/d91 -o 88080480 -b 14680064 ==Total 7 GB... (4 Replies)
Discussion started by: sahil_shine
4 Replies
4. AIX
Please consider this a question about basics&best practices. On AIX 5.3 system, three raw physical volumes are defined from storage. While doing a read with command dd from the raw device, the speed rate is 250Mb/s.
Then, it gets complex when I define these three pv's to an lv of type raw. Doing... (4 Replies)
Discussion started by: royalliege
4 Replies
5. Solaris
Hi,
I am using Sun Solaris 10 (Sparc 64 bit),
I have a meta device /dev/dsk/emcpower26a mounting on /u01. I want to make this metadeice as raw device.
Need solaris command to remove file system and make it as raw device ?.
Is there any solaris command to check raw devices ?.
Thanks (1 Reply)
Discussion started by: zeeshan047
1 Replies
6. Solaris
Hi,
I need to create 4 zones.
I have an array with a RAID5 volume. I have exported 4 LUNS from the array. Now my host see the 4 LUNS as raw devices.
I am partitioning each LUN using format then mounting each slice on the global zone. Then I am using each slice as a file system for my non... (3 Replies)
Discussion started by: general_lee
3 Replies
7. Solaris
Hi,
I'm trying to find out how to see used space on RAW device.
I tried with prtvtoc -f RAWdevice but for 3 different device I'm getting the same FREE_SIZE which look a bit impossible.
root@zg8cscfb1> prtvtoc -f /dev/md/redodg/rdsk/d300
FREE_START=0 FREE_SIZE=20352 FREE_COUNT=1 FREE_PART=... (2 Replies)
Discussion started by: MarioT
2 Replies
8. Red Hat
Hi,
How to find the raw device/multipath details of the LUN used by the diskgroups of the database.
file system type -- ASM
Oracle -- 11.2.0.3.0
OS -- Linux
This is RAC database.
Regards,
Maddy (2 Replies)
Discussion started by: Maddy123
2 Replies
LEARN ABOUT MOJAVE
service
SERVICE(8) System Manager's Manual SERVICE(8)
NAME
service - run a System V init script
SYNOPSIS
service SCRIPT COMMAND [OPTIONS]
service --status-all
service --help | -h | --version
DESCRIPTION
service runs a System V init script or systemd unit in as predictable an environment as possible, removing most environment variables and
with the current working directory set to /.
The SCRIPT parameter specifies a System V init script, located in /etc/init.d/SCRIPT, or the name of a systemd unit. The existence of a
systemd unit of the same name as a script in /etc/init.d will cause the unit to take precedence over the init.d script. The supported val-
ues of COMMAND depend on the invoked script. service passes COMMAND and OPTIONS to the init script unmodified. For systemd units, start,
stop, status, and reload are passed through to their systemctl/initctl equivalents.
All scripts should support at least the start and stop commands. As a special case, if COMMAND is --full-restart, the script is run twice,
first with the stop command, then with the start command.
service --status-all runs all init scripts, in alphabetical order, with the status command. The status is [ + ] for running services, [ - ]
for stopped services and [ ? ] for services without a status command. This option only calls status for sysvinit jobs.
EXIT CODES
service calls the init script and returns the status returned by it.
FILES
/etc/init.d
The directory containing System V init scripts.
/{lib,run,etc}/systemd/system
The directories containing systemd units.
ENVIRONMENT
LANG, LANGUAGE, LC_CTYPE, LC_NUMERIC, LC_TIME, LC_COLLATE, LC_MONETARY, LC_MESSAGES, LC_PAPER, LC_NAME, LC_ADDRESS, LC_TELEPHONE, LC_MEA-
SUREMENT, LC_IDENTIFICATION, LC_ALL, TERM, PATH
The only environment variables passed to the init scripts.
SEE ALSO
/etc/init.d/skeleton
update-rc.d(8)
init(8)
invoke-rc.d(8)
systemctl(1)
AUTHOR
Miloslav Trmac <mitr@redhat.com>, Petter Reinholdtsen <pere@hungry.com>
Licence: GNU Public Licence v2 (GPLv2)
COPYRIGHT
2006 Red Hat, Inc., Petter Reinholdtsen <pere@hungry.com>
Jan 206 SERVICE(8)