04-09-2013
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have a quad ethernet card in my sun box, and only 3 of them are visable when I "ifconfig -a". How do I activate the the 4th one? I think it is solaris 5.6. Thanks.
Marc (1 Reply)
Discussion started by: mmaniscalco
1 Replies
2. HP-UX
Hello all,
I want to add a new virtual interface on HP-UX B.11.11 U 9000/800 box.
I know that ifconfig can be used to add the Virtual interface.
BUt i do not know the exact syntax. it some times gives plumb error if i try to add
# ifconfig vif0 10.1.10.1 up
plumb error: No such file... (3 Replies)
Discussion started by: supersumanth
3 Replies
3. Solaris
Hello,
I have a SunOS (5.5.1) system that I need to migrate to a new IP address. I would like to have any requests destined for the old IP to be forwarded to this server.
One suggestion I had was to add a route on my router that would point the old IP to the new IP.
How do I add another... (2 Replies)
Discussion started by: reiklen
2 Replies
4. Red Hat
Netdump over bonded interface ?
Hey there,..
I have heard from admins, that netdump usually fails over a bonded network interface.
I have written a multi-OS checkdump script , which checks if the respective crashdump utility on corresponding OS is correctly configured, space is available,... (1 Reply)
Discussion started by: shriyer
1 Replies
5. Solaris
Please , I have a problem
I have add a statis route on Solaris 10, but after this, the network interface of Server was Offline.
The system is in cluster mode (3.2)
route add -net 10.10.1.128 -netmask 255.255.255.128 10.10.1.51
-------------------
lo0:... (1 Reply)
Discussion started by: Ruggero
1 Replies
6. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
7. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
8. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
9. AIX
Hi Everyone,
Is it possible to configure bonding over bonded interface in AIX?
For example:
server has for NIC port:
ent0
ent1
ent2
ent3
First I create a EtherChannel ent4 from ent0 and ent1.
and then I create a EtherChannel ent5 from ent2 and ent3.
Can I create a EtherChannel... (1 Reply)
Discussion started by: nnnnnnine
1 Replies
LEARN ABOUT CENTOS
bond2team
BOND2TEAM(1) Bonding to Team conversion tool BOND2TEAM(1)
NAME
bond2team -- Converts bonding configuration to team
SYNOPSIS
bond2team [options]
DESCRIPTION
bond2team is a tool to convert bonding options to team trying as much as possible to keep the original functionality.
The resulting files are saved in a temporary directory using ifcfg style by default. In the case of converting an ifcfg file, it translates
the bonding options to team, preserving all other options. In that case, it converts the respective slave ifcfg files to team port, pre-
serving all their other options too. In case of converting from given bonding options in the command line, the tool can use the specified
ports as team ports.
OPTIONS
--master <interface>
Specify the interface name or ifcfg file to convert. If the interface name is specified, the tool will look at
/etc/sysconfig/network-scripts/ for the respective ifcfg file.
--rename <interface>
This is a convenient option to replace the original interface name by the specified name. For instance, if --master specifies bond0,
it is possible to use --rename team0 to change the final interface name to team0.
--ifcfg
Set the output format to ifcfg config style. [default]
--json Set the output format to JSON style. See teamd.conf(5) for further details.
--bonding_opts '<bonding options>'
Specify the bonding options to be converted instead of reading them from the ifcfg file.
--port <interface>
Set the specified interface as a team port.
--configdir <directory>
Change the ifcfg configuration path from /etc/sysconfig/network-scripts to the specified <directory>.
--outputdir <directory>
Set the output directory to <directory>.
--stdout
Print the result to the screen instead of writing to files.
--debug
Increase the debugging level.
--quiet
Disallow any messages to be printed to console.
--version
Print tool version to console and exit.
--help Print help text to console and exit.
--examples
Print common usage examples to console and exit.
EXAMPLES
To convert the current 'bond0' ifcfg configuration to team ifcfg:
# bond2team --master bond0
To convert the current 'bond0' ifcfg configuration to team ifcfg renaming the interface name to 'team0'. Caution : firewall rules, alias
interfaces, etc., that might be tied to the original interface name can break after the renaming because the tool will only change the
ifcfg file, nothing else.
# bond2team --master bond0 --rename team0
To convert given bonding parameters with ports without any ifcfg:
# bond2team --bonding_opts 'mode=1 miimon=500 primary=eth1 primary_reselect=0' --port eth1 --port eth2 --port eth3 --port eth4
For more examples, see the option --examples.
CAVEATS
The tool will not convert any other configuration which might be tied to the current setup. For instance, firewall rules, alias interfaces,
bridges, and so on.
AUTHOR
Flavio Leitner is the original author of the tool. Jiri Pirko is the original author and current maintainer of libteam.
SEE ALSO
teamd(8), teamdctl(8), teamd.conf(5), teamnl(8)
libteam 2013-07-18 BOND2TEAM(1)