I have a serial console cable connecting my Desktop to the p520 box and am therefore able to get to the VIOS LPAR via HyperTerminal. From that I can also get to both AIX LPARs using the "mkvt -id x" command
Here's the output from that command from the box
Surely I am not the only one trying this combination?
I'll start researching that line of thinking and see what comes out.
I am posting this as an FYI. I burned a lot of time on digging for this solution. The problem was performance between newer AIX p series boxes and a sun 4500 with a fiber nic. I tried many misc. solutions but this turned out to fix the issue. My bandwidth benchmark went from around 20MB/sec to... (1 Reply)
I have a system model 505 p server. I am trying to virtualize my server. My network admin has given me 10 IP addresses (with the DNS already updated with names that map onto each ip). E.g.: IP1 maps to m1.lab, IP2 maps to m2.lab, etc
I have been following the redpaper "Integrated Virtualization... (0 Replies)
Hello
I have a system with four AIX 5L V5.3 partitions and a Virtual I/O server, connected to a a DS4800 storage array.
Now the company bought another DS4800... i made raid on it... and now i wanna give LUN's to the VIOS, so i can use in one of AIX partitions...
Someone can help me?
... (5 Replies)
Hi,
When I try to create a virtual disk in IVM ( integrated Virtual Machine VIO ) I get this message
Problems occurred while processing the data. A summary of all problems for this page are listed below. Additional details for each problem may be located next to the field causing the... (0 Replies)
Hi everyone,
Sorry if this post is in the wrong place. I searched the forums for "IVM" and it turned up no results. Hopefully someone knows about this. My dilemma is that I have multiple IBM JS12 Express blades in our blade center, each running VIOS 2.1.0.10-FP-20.1 and hosting a couple LPARs. Out... (2 Replies)
Hi,
When I try to login on my vios ivm website http://vios through the browser -- all three of them -- firefox , chrome , Internet Explorer , i get this error
http://vioserver/j_security_check
I have java installed on the machine from where i am trying to open up the IVM/VIOS webpage.
I... (2 Replies)
I am facing problems in moving CD-ROM from one lpar to another.
CDROM can be seen on the POWERVM (IVM) server , but through the web-access if I move it ( assign it ) to LPAR it will be assigned. I run cfgmgr , and the cdrom does not show up in the LPAR. I firmly believe this is the reason why I... (2 Replies)
Hello,
I have a problem to list my active partitions with PowerVM IVM,
Vios has an error message , can't open lparUtil.log ,
the df command tells us that /dev/hd9var is 100% used, laprUtil.log file is 0 Ko !!
i don't know what i can delete to free space,
the file is locked , i... (2 Replies)
Hello,
After installing on P6 which is POWERVM IVM VIOS enabled (VET CODE D21C77ACD9229817CA1F00002C10004164 )
i get this message
"I/O hosting requires a hosting partition - boot not permitted".
HMC was connected to the machine
then HMC was removed through ASMI
Searching on... (2 Replies)
Hello,
I have some unclear about how VIOS uses its resources.
Assume that VIOS lpar has only 1 physical FC, and we use that to connect to the Lun. Then we install VIOS for the lpar on that Lun.
So my question is, afterward, we can still use that physical FC for the virtual FC we create... (3 Replies)
Discussion started by: Phat
3 Replies
LEARN ABOUT NETBSD
cz
CZ(4) BSD Kernel Interfaces Manual CZ(4)NAME
cz -- Cyclades-Z series multi-port serial adapter device driver
SYNOPSIS
cz* at pci? dev ? function ?
DESCRIPTION
The cz device driver supports the Cyclades-Z series of multi-port serial adapters. The Cyclades-Z is an intelligent serial controller com-
prising:
o PLX9060ES PCI bus interface
o Xilinx XC5204 FPGA
o IDT R3052 MIPS CPU
The MIPS CPU runs firmware provided by the device driver. Communication with the MIPS is performed by modifying data structures located in
board local RAM or host RAM.
The Cyclades-Z comes in three basic flavors:
o Cyclades-8Zo rev. 1 -- This is an older 8-port board with no FPGA. The serial ports are provided by an octopus cable.
o Cyclades-8Zo rev. 2 -- This is the newer 8-port board. The serial ports are provided by an octopus cable.
o Cyclades-Ze -- This is the expandable version of the Cyclades-Z. It uses an HD-50 SCSI cable to connect the board to a 1U rack
mountable serial expansion box. Each box has 16 RJ45 serial ports, and up to 4 boxes may be chained together, for a total of 64
ports. Boxes 3 and 4 require their own external power supply, otherwise the firmware will refuse to start (as it cannot communi-
cate with the UARTs in those boxes).
The Cyclades-Z has several features to improve performance under high serial I/O load:
o The board may operate in interrupt-driven mode or polled mode to reduce interrupt load.
o Each channel has a large input and output buffer.
o Each channel may be programmed to generate an interrupt based on reception of a specific character, e.g. a PPP End-Of-Frame charac-
ter.
o The MIPS CPU on the board performs all flow-control handling.
FILES
/dev/ttyCZnnnn -- dial-in (normal) TTY device
/dev/dtyCZnnnn -- dial-out TTY device
SEE ALSO pci(4), termios(4), tty(4)HISTORY
The cz driver first appeared in NetBSD 1.5.
AUTHORS
The cz driver was written by Jason R. Thorpe <thorpej@zembu.com> and
Bill Studenmund <wrstuden@zembu.com> of Zembu Labs, Inc.
BUGS
The cz driver does not currently implement communication via host RAM. While this may improve performance by reducing the number of PCI mem-
ory space read/write cycles, it is not straightforward to implement with the current bus_dma(9) API.
Interrupt mode has not been tested.
There is no support for reading or writing the EEPROM connected to the PLX PCI bus controller.
BSD May 17, 2000 BSD