03-15-2013
I saw the page about dladm, but for some reasons, some of those sub-commands are not available on my server (i.e. rename-link, show-phys, ...)
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. UNIX for Advanced & Expert Users
Hi all,
I'm using an HP Proliant server with double NIC and Debian 5 (Lenny) as its OS. I used link bonding on it for several years with no problem.
Today, (now only one interface connected to switch) the interface went down. I restarted networking service (/etc/init.d/networking restart) and... (7 Replies)
Discussion started by: mjdousti
7 Replies
3. Solaris
HI,
genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
genunix: WARNING: ce0: fault detected external to device; service degraded
genunix: WARNING: ce0: xcvr addr:0x01 - link down
genunix: NOTICE: ce0: fault cleared external to device; service available
genunix: ... (4 Replies)
Discussion started by: sunnybee
4 Replies
4. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
5. UNIX for Advanced & Expert Users
hi
I have a question,
eth0 : 192.168.2.10
eth1: 192.168. 2.11
subnet : 255.255.255.0
eth0 and eth1 plug same swich
I want communication between the two interface one host examp :
ping 192.168.2.10 -I eth1
ping 192.168.2.11 -I eth0
but not respons.. pls helme (3 Replies)
Discussion started by: sadosan83
3 Replies
6. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
7. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
8. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
link(1) General Commands Manual link(1)
NAME
link, unlink - Creates an additional directory entry for an existing file
SYNOPSIS
link file1 file2
unlink file
STANDARDS
Interfaces documented on this reference page conform to industry standards as follows:
link: XCU5.0
unlink: XCU5.0
Refer to the standards(5) reference page for more information about industry standards and associated tags.
DESCRIPTION
The link command performs the link() system call to create an additional directory entry for an existing file, file1. In effect, the
underlying file then has two names, file1 and file2 (either of these arguments can be a pathname). The old and new entries share equal
access rights to the underlying file.
The unlink command performs the unlink() system call to remove a link to file created by link. The unlink command removes the directory
entry specified by the file parameter and, if the entry is a hard link, decrements the link count of the file referenced by the link.
You should be familiar with the link() and unlink() system calls before you use these commands.
The link and unlink commands do not issue error messages when the associated system call is unsuccessful.
NOTES
The link and unlink commands cannot be used to link and unlink directories.
EXIT STATUS
The link and unlink commands both exit with the following: The link() or unlink() system call succeeded. Too few or too many arguments
specified. The link() or unlink() system call failed.
SEE ALSO
Commands: fsck(8), ln(1)
Functions: link(2), unlink(2)
link(1)