03-15-2013
Rename network interface
Hi all, I'm new here and looking for some help.
I'm looking for the way to rename the network interfaces for Solaris 10. Got a server with 2 network cards (say "igb0" and "igb1") and there were some reasons that I have to swap the pci slots for those cards. However, after I did that, Solaris 10 seems to detect them as new cards and created new names "igb2" and "igb3", which basically screwed up my network settings.
I prefer to keep my network settings so been trying to find out the way to rename them back to "igb0" and "igb1".
Any suggestion would be appreciated.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. UNIX for Advanced & Expert Users
Hi all,
I'm using an HP Proliant server with double NIC and Debian 5 (Lenny) as its OS. I used link bonding on it for several years with no problem.
Today, (now only one interface connected to switch) the interface went down. I restarted networking service (/etc/init.d/networking restart) and... (7 Replies)
Discussion started by: mjdousti
7 Replies
3. Solaris
HI,
genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
genunix: WARNING: ce0: fault detected external to device; service degraded
genunix: WARNING: ce0: xcvr addr:0x01 - link down
genunix: NOTICE: ce0: fault cleared external to device; service available
genunix: ... (4 Replies)
Discussion started by: sunnybee
4 Replies
4. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
5. UNIX for Advanced & Expert Users
hi
I have a question,
eth0 : 192.168.2.10
eth1: 192.168. 2.11
subnet : 255.255.255.0
eth0 and eth1 plug same swich
I want communication between the two interface one host examp :
ping 192.168.2.10 -I eth1
ping 192.168.2.11 -I eth0
but not respons.. pls helme (3 Replies)
Discussion started by: sadosan83
3 Replies
6. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
7. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
8. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT SUNOS
systemd-networkd.service
SYSTEMD-NETWORKD.SERVICE(8) systemd-networkd.service SYSTEMD-NETWORKD.SERVICE(8)
NAME
systemd-networkd.service, systemd-networkd - Network manager
SYNOPSIS
systemd-networkd.service
/lib/systemd/systemd-networkd
DESCRIPTION
systemd-networkd is a system service that manages networks. It detects and configures network devices as they appear, as well as creating
virtual network devices.
To configure low-level link settings independently of networks, see systemd.link(5).
systemd-networkd will create network devices based on the configuration in systemd.netdev(5) files, respecting the [Match] sections in
those files.
systemd-networkd will manage network addresses and routes for any link for which it finds a .network file with an appropriate [Match]
section, see systemd.network(5). For those links, it will flush existing network addresses and routes when bringing up the device. Any
links not matched by one of the .network files will be ignored. It is also possible to explicitly tell systemd-networkd to ignore a link by
using Unmanaged=yes option, see systemd.network(5).
When systemd-networkd exits, it generally leaves existing network devices and configuration intact. This makes it possible to transition
from the initrams and to restart the service without breaking connectivity. This also means that when configuration is updated and
systemd-networkd is restarted, netdev interfaces for which configuration was removed will not be dropped, and may need to be cleaned up
manually.
CONFIGURATION FILES
The configuration files are read from the files located in the system network directory /lib/systemd/network, the volatile runtime network
directory /run/systemd/network and the local administration network directory /etc/systemd/network.
Networks are configured in .network files, see systemd.network(5), and virtual network devices are configured in .netdev files, see
systemd.netdev(5).
SEE ALSO
systemd(1), systemd.link(5), systemd.network(5), systemd.netdev(5), systemd-networkd-wait-online.service(8)
systemd 237 SYSTEMD-NETWORKD.SERVICE(8)