03-09-2013
nothing was done on the server,
but yes one observation, though it doesn't show running state but the ip defined on this interface is well reachable from another node. This eliminated my suspicion on the cable part. I also restarted the whole server as well but no luck.
Can someone advice further ??
10 More Discussions You Might Find Interesting
1. Solaris
Hi
I'm having a big trouble running a configuration tool (ftamtool) which uses xview on sunos 5.8, it refuses to start and says: XView error: could not load font 'FONT_FAMILY_SANS_SERIF...
How to force the program to use installed fonts and where are fonts installed available to use ?
... (0 Replies)
Discussion started by: andryk
0 Replies
2. IP Networking
I'm trying to plumb a new interface bge1 on my machine:
root@obms2-com-indianapolis-in:/root# ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet... (3 Replies)
Discussion started by: R37ribution
3 Replies
3. Shell Programming and Scripting
I am looking to get a report on autosys jobs in RUNNING state b/w certain time frame (timeA and timeB).
What I am after is the list of all the jobs that ran between AND during timeA and timeB.
Jobs within the timeframe could either:
A: STARTING --> RUNNING --> SUCCESS/FAILURE etc..
B: ... (0 Replies)
Discussion started by: rgilan01
0 Replies
4. Programming
I am looking to get a report on autosys jobs in RUNNING state b/w certain time frame (timeA and timeB).
What I am after is the list of all the jobs that ran between AND during timeA and timeB.
Jobs within the timeframe could either:
A: STARTING --> RUNNING --> SUCCESS/FAILURE etc..
B: ... (0 Replies)
Discussion started by: rgilan01
0 Replies
5. Solaris
I am looking to get a report on autosys jobs in RUNNING state b/w certain time frame (timeA and timeB).
What I am after is the list of all the jobs that ran between AND during timeA and timeB.
Jobs within the timeframe could either:
A: STARTING --> RUNNING --> SUCCESS/FAILURE etc..
B: ... (2 Replies)
Discussion started by: rgilan01
2 Replies
6. Solaris
Hi all,
I encounter some problem with my e1000g interface running on sol 10. I can't permanently change the auto-nego to disable, if i use ndd commands, it will only stay until the next reboot.
But i can't change the link speed either is set to /etc/init.d/nddconfig or using ndd commands.
... (1 Reply)
Discussion started by: mailbox80
1 Replies
7. Solaris
hi frineds
in sunfire 6800 server for one domain when ever i am giving ifconfig -a interface names like hme0,hme1.......are not showing.Actually in the server hme0,hme1,qfe are showing .when i was tried with the cat /etc/path_to_intstshowing tphysical interfcace names .
after giving the... (2 Replies)
Discussion started by: tv.praveenkumar
2 Replies
8. AIX
Hi Admins,
I am having a whole system lpar in open firmware state on HMC.
How can I bring it to running state ?
Let me know. Thanks. (2 Replies)
Discussion started by: snchaudhari2
2 Replies
9. Solaris
on both of my T2000 I am seeing same values of 100Mbps for e1000g0 ethernet port.
i know all four ethernet ports on T2000 are gigabit ports so why is my first link showing as 100Mbps and how can i correct it?
# dladm show-dev
e1000g0 link: up speed: 100 Mbps ... (1 Reply)
Discussion started by: aliyesami
1 Replies
10. Solaris
Hi All,
Please let me know the step by step process to set the e1000g0 interface speed to 1000mbps with full duplex from 100fdx and how to disable the auto negotiation with switch?.
Thanks and Regards,
Ganesh. (7 Replies)
Discussion started by: gsrungav
7 Replies
ypset(8) System Manager's Manual ypset(8)
NAME
ypset - bind ypbind to a particular NIS server
SYNOPSIS
ypset [ -d domain ] [ -h hostname ] server
DESCRIPTION
In order to run ypset, ypbind must be initiated with the -ypset or -ypsetme options. See ypbind(8). ypset tells ypbind to get NIS ser-
vices for the specified domain from the ypserv(8) process running on server.
In cases where several hosts on the local net are supplying NIS services, it is possible for ypbind to rebind to another host even while
you attempt to find out if the ypset operation succeeded. For example, you can type:
example% ypset host1
example% ypwhich
host2
which can be confusing. This is a function of the NIS subsystem's attempt to know always a running NIS server, and occurs when host1 does
not respond to ypbind because it is not running ypserv (or is overloaded), and host2, running ypserv, gets the binding.
Server indicates the NIS server to bind to, and must be specified as a name or an IP address. This will work only if the node has a cur-
rent valid binding for the domain in question, and ypbind has been set to allow use of ypset. In most cases, server should be specified
as an IP address.
OPTIONS
-d domain
Specify a domain other than the default domain as returned by domainname(8).
-h hostname
Set the NIS binding on host hostname
instead of the local machine.
SEE ALSO
domainname(8), ypbind(8), ypcat(8), ypmatch(1), ypserv(8), yppoll(8), ypwhich(1)
AUTHOR
ypset is part of the yp-tools package, which was written by Thorsten Kukuk <kukuk@linux-nis.org>.
YP Tools 2.14 April 2010 ypset(8)