Sponsored Content
Operating Systems Solaris Interface e1000g0 not showing in running state Post 302777933 by fpmurphy on Friday 8th of March 2013 06:34:20 PM
Old 03-08-2013
What changes did you make to your system? Did you edit any files such as /etc/hostname.e1000g0?
This User Gave Thanks to fpmurphy For This Post:
 

10 More Discussions You Might Find Interesting

1. Solaris

Interface not showing : Xview error

Hi I'm having a big trouble running a configuration tool (ftamtool) which uses xview on sunos 5.8, it refuses to start and says: XView error: could not load font 'FONT_FAMILY_SANS_SERIF... How to force the program to use installed fonts and where are fonts installed available to use ? ... (0 Replies)
Discussion started by: andryk
0 Replies

2. IP Networking

Solaris 9 new pumbed interface will not enter a RUNNING state

I'm trying to plumb a new interface bge1 on my machine: root@obms2-com-indianapolis-in:/root# ifconfig -a lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2 inet... (3 Replies)
Discussion started by: R37ribution
3 Replies

3. Shell Programming and Scripting

report of autosys job in RUNNING state

I am looking to get a report on autosys jobs in RUNNING state b/w certain time frame (timeA and timeB). What I am after is the list of all the jobs that ran between AND during timeA and timeB. Jobs within the timeframe could either: A: STARTING --> RUNNING --> SUCCESS/FAILURE etc.. B: ... (0 Replies)
Discussion started by: rgilan01
0 Replies

4. Programming

report of autosys job in RUNNING state

I am looking to get a report on autosys jobs in RUNNING state b/w certain time frame (timeA and timeB). What I am after is the list of all the jobs that ran between AND during timeA and timeB. Jobs within the timeframe could either: A: STARTING --> RUNNING --> SUCCESS/FAILURE etc.. B: ... (0 Replies)
Discussion started by: rgilan01
0 Replies

5. Solaris

report of autosys job in RUNNING state

I am looking to get a report on autosys jobs in RUNNING state b/w certain time frame (timeA and timeB). What I am after is the list of all the jobs that ran between AND during timeA and timeB. Jobs within the timeframe could either: A: STARTING --> RUNNING --> SUCCESS/FAILURE etc.. B: ... (2 Replies)
Discussion started by: rgilan01
2 Replies

6. Solaris

how to force e1000g0 interface in solaris 10

Hi all, I encounter some problem with my e1000g interface running on sol 10. I can't permanently change the auto-nego to disable, if i use ndd commands, it will only stay until the next reboot. But i can't change the link speed either is set to /etc/init.d/nddconfig or using ndd commands. ... (1 Reply)
Discussion started by: mailbox80
1 Replies

7. Solaris

Not showing n/w interface name in Solaris with ifconfig -a

hi frineds in sunfire 6800 server for one domain when ever i am giving ifconfig -a interface names like hme0,hme1.......are not showing.Actually in the server hme0,hme1,qfe are showing .when i was tried with the cat /etc/path_to_intstshowing tphysical interfcace names . after giving the... (2 Replies)
Discussion started by: tv.praveenkumar
2 Replies

8. AIX

Open firmware state to running state

Hi Admins, I am having a whole system lpar in open firmware state on HMC. How can I bring it to running state ? Let me know. Thanks. (2 Replies)
Discussion started by: snchaudhari2
2 Replies

9. Solaris

Network interface showing wrong configuratoin

on both of my T2000 I am seeing same values of 100Mbps for e1000g0 ethernet port. i know all four ethernet ports on T2000 are gigabit ports so why is my first link showing as 100Mbps and how can i correct it? # dladm show-dev e1000g0 link: up speed: 100 Mbps ... (1 Reply)
Discussion started by: aliyesami
1 Replies

10. Solaris

How to increase the e1000g0 interface speed in Solaris?

Hi All, Please let me know the step by step process to set the e1000g0 interface speed to 1000mbps with full duplex from 100fdx and how to disable the auto negotiation with switch?. Thanks and Regards, Ganesh. (7 Replies)
Discussion started by: gsrungav
7 Replies
HOSTNAME(5)							     hostname							       HOSTNAME(5)

NAME
hostname - Local hostname configuration file SYNOPSIS
/etc/hostname DESCRIPTION
The /etc/hostname file configures the name of the local system that is set during boot using the sethostname(2) system call. It should contain a single newline-terminated hostname string. The hostname may be a free-form string up to 64 characters in length; however, it is recommended that it consists only of 7-bit ASCII lower-case characters and no spaces or dots, and limits itself to the format allowed for DNS domain name labels, even though this is not a strict requirement. Depending on the operating system, other configuration files might be checked for configuration of the hostname as well, however only as fallback. You may use hostnamectl(1) to change the value of this file from the command line. HISTORY
The simple configuration file format of /etc/hostname originates from Debian GNU/Linux. SEE ALSO
systemd(1), sethostname(2), hostname(1), hostname(7), machine-id(5), machine-info(5), hostnamectl(1), systemd-hostnamed.service(8) systemd 208 HOSTNAME(5)
All times are GMT -4. The time now is 06:28 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy