YPBIND(8)						    BSD System Manager's Manual 						 YPBIND(8)

NAME

     ypbind -- NIS domain binding daemon

SYNOPSIS

     ypbind [-ypset] [-ypsetme] [-s] [-m] [-S domainname,server1,server2,...]

DESCRIPTION

     The ypbind utility is the process that maintains NIS binding information.	At startup, it searches for an NIS server responsible for serving
     the system's default domain (as set by the domainname(1) command) using network broadcasts.  Once it receives a reply, it will store the
     address of the server and other information in a special file located in /var/yp/binding.	The NIS routines in the standard C library can
     then use this file when processing NIS requests.  There may be several such files since it is possible for an NIS client to be bound to more
     than one domain.

     After a binding has been established, ypbind will send DOMAIN_NONACK requests to the NIS server at one minute intervals.  If it fails to
     receive a reply to one of these requests, ypbind assumes that the server is no longer running and resumes its network broadcasts until
     another binding is established.  The ypbind utility will also log warning messages using the syslog(3) facility each time it detects that a
     server has stopped responding, as well as when it has bound to a new server.

     The following options are available:

     -ypset  It is possible to force ypbind to bind to a particular NIS server host for a given domain by using the ypset(8) command.  However,
	     ypbind refuses YPBINDPROC_SETDOM requests by default since it has no way of knowing exactly who is sending them.  Using the -ypset
	     flag causes ypbind to accept YPBINDPROC_SETDOM requests from any host.  This option should only be used for diagnostic purposes and
	     only for limited periods since allowing arbitrary users to reset the binding of an NIS client poses a severe security risk.

     -ypsetme
	     This is similar to the -ypset flag, except that it only permits YPBINDPROC_SETDOM requests to be processed if they originated from
	     the local host.

     -s      Cause ypbind to run in secure mode: it will refuse to bind to any NIS server that is not running as root (i.e., that is not using
	     privileged TCP ports).

     -S domainname,server1,server2,server3,...
	     Allow the system administrator to lock ypbind to a particular domain and group of NIS servers.  Up to ten servers can be specified.
	     There must not be any spaces between the commas in the domain/server specification.  This option is used to ensure that the system
	     binds only to one domain and only to one of the specified servers, which is useful for systems that are both NIS servers and NIS
	     clients: it provides a way to restrict what machines the system can bind to without the need for specifying the -ypset or -ypsetme
	     options, which are often considered to be security holes.	The specified servers must have valid entries in the local /etc/hosts
	     file.  IP addresses may be specified in place of hostnames.  If ypbind cannot make sense out of the arguments, it will ignore the -S
	     flag and continue running normally.

	     Note that ypbind will consider the domainname specified with the -S flag to be the system default domain.

     -m      Cause ypbind to use a 'many-cast' rather than a broadcast for choosing a server from the restricted mode server list.  In many-cast
	     mode, ypbind will transmit directly to the YPPROC_DOMAIN_NONACK procedure of the servers specified in the restricted list and bind to
	     the server that responds the fastest.  This mode of operation is useful for NIS clients on remote subnets where no local NIS servers
	     are available.  The -m flag can only be used in conjunction with the -S flag above (if used without the -S flag, it has no effect).

NOTES

     The ypbind utility will not make continuous attempts to keep secondary domains bound.  If a server for a secondary domain fails to respond to
     a ping, ypbind will broadcast for a new server only once before giving up.  If a client program attempts to reference the unbound domain,
     ypbind will try broadcasting again.  By contrast, ypbind will automatically maintain a binding for the default domain whether client programs
     reference it ot not.

FILES

     /var/yp/binding/[domainname].[version]
		   the files used to hold binding information for each NIS domain
     /etc/rc.conf  system configuration file where the system default domain and ypbind startup options are specified

SEE ALSO

     domainname(1), syslog(3), yp(8), ypserv(8), ypset(8)

AUTHORS

     Theo de Raadt <deraadt@fsa.ca>

BSD
								   April 9, 1995							       BSD