I've been looking around various forums for this problem.
Some say that the drivers are on the Solaris 10 distribution CD/DVD in the guise of packages TSIgfx and TSIgfxw. Also mentioned are TSIpgx and TSIpgxw.
Can you try:
for all 4 of these to see if any exist on your system.
Could also try:
to try to install them.
Also, do note that you will need to reconfigure the kernel after installing the driver to get Solaris to look for it.
It also seems to be the case that if the driver for PGX32 is installed you'll have /dev/fbs present.
Hello everybody!!
I need your help again.
I am using Sun Ultra sparc 60 machine.Follwing are the types of files getting generated in /var/tmp.
"windu_sm_o aaaa,baaa,caaa,daaa" etc.
I am not able to locate which application is generating these files.
Can I straightway delete these files ? or... (1 Reply)
Dear All,
I have trouble, I have SPARC Machine and when start for loading, can not finish !
this is copy off message from my system
Netra t 1120/1125 (UltraSPARC-II 440MHz), No Keyboard
OpenBoot 3.31, 512 MB memory installed, Serial #12116535.
Ethernet address 8:0:20:b8:e2:37, Host ID:... (4 Replies)
I have an ultra sparc 2 with no video - I connect to it with hyperterm.
Is there a way to get to the OK prompt? I have tried control/break and that does not work.
If not is there a video card I can get to put in this box?
I have Solaris 10 installed on this machine.
Thanks (7 Replies)
Comments/Problems:
Machine boots from CDROM, starts SILO Version 1.4.13,
display welcome message (welcome to Debian GNU/Linux lenny!
built on 20081218-10:06 ).
boot:
Allocated 8 Megs of memory at 0x40000000 for kernel
Loaded kernel version 2.6.26
Loading initial ramdisk... (3 Replies)
Dear Guru,
My boss has a plan to upgrade cpu of server so he needs to know how much better performance(percentage) is Ultra SPARC IV+ 1.95 GHz than Ultra SPARC IV 1.35 GHz?.
I am looking for documentation to reference but I didn't see anything close to my point. If who know,... (3 Replies)
Hi all.
I am seeing in one of our less-used servers that it crashed and now won't restart. I get the message 'continue with normal startup or boot into maintenance mode'.
I go into maintenance and run fsck on /usr0 (mentioned in error at restart) it then reboots but goes right back to... (3 Replies)
I have a Sun Blade 1000 machine that I installed Ubuntu 7.10 SPARC onto. The only user configured (configure during install) cannot use sudo. When I try to issue a command using sudo (ex. sudo apt-get install) it asks me for my password and returns the error "user not found in sudoers file". I need... (4 Replies)
Hi all,
I managed to salvage form work an old Sun Sparc Ultra 30. I have had it stored (controlled storage) for a few years and decided to get it home and boot it up.
It starts up with a beep then I can hear disks spinning up, CDROM moving but nothing is displayed on the monitor.
Can... (2 Replies)
Discussion started by: robbo007
2 Replies
LEARN ABOUT DEBIAN
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)