I've been looking around various forums for this problem.
Some say that the drivers are on the Solaris 10 distribution CD/DVD in the guise of packages TSIgfx and TSIgfxw. Also mentioned are TSIpgx and TSIpgxw.
Can you try:
Code:
pkginfo <package name>
for all 4 of these to see if any exist on your system.
Could also try:
Code:
pkgadd <package name>
to try to install them.
Also, do note that you will need to reconfigure the kernel after installing the driver to get Solaris to look for it.
Code:
boot -r
It also seems to be the case that if the driver for PGX32 is installed you'll have /dev/fbs present.
Hello everybody!!
I need your help again.
I am using Sun Ultra sparc 60 machine.Follwing are the types of files getting generated in /var/tmp.
"windu_sm_o aaaa,baaa,caaa,daaa" etc.
I am not able to locate which application is generating these files.
Can I straightway delete these files ? or... (1 Reply)
Dear All,
I have trouble, I have SPARC Machine and when start for loading, can not finish !
this is copy off message from my system
Netra t 1120/1125 (UltraSPARC-II 440MHz), No Keyboard
OpenBoot 3.31, 512 MB memory installed, Serial #12116535.
Ethernet address 8:0:20:b8:e2:37, Host ID:... (4 Replies)
I have an ultra sparc 2 with no video - I connect to it with hyperterm.
Is there a way to get to the OK prompt? I have tried control/break and that does not work.
If not is there a video card I can get to put in this box?
I have Solaris 10 installed on this machine.
Thanks (7 Replies)
Comments/Problems:
Machine boots from CDROM, starts SILO Version 1.4.13,
display welcome message (welcome to Debian GNU/Linux lenny!
built on 20081218-10:06 ).
boot:
Allocated 8 Megs of memory at 0x40000000 for kernel
Loaded kernel version 2.6.26
Loading initial ramdisk... (3 Replies)
Dear Guru,
My boss has a plan to upgrade cpu of server so he needs to know how much better performance(percentage) is Ultra SPARC IV+ 1.95 GHz than Ultra SPARC IV 1.35 GHz?.
I am looking for documentation to reference but I didn't see anything close to my point. If who know,... (3 Replies)
Hi all.
I am seeing in one of our less-used servers that it crashed and now won't restart. I get the message 'continue with normal startup or boot into maintenance mode'.
I go into maintenance and run fsck on /usr0 (mentioned in error at restart) it then reboots but goes right back to... (3 Replies)
I have a Sun Blade 1000 machine that I installed Ubuntu 7.10 SPARC onto. The only user configured (configure during install) cannot use sudo. When I try to issue a command using sudo (ex. sudo apt-get install) it asks me for my password and returns the error "user not found in sudoers file". I need... (4 Replies)
Hi all,
I managed to salvage form work an old Sun Sparc Ultra 30. I have had it stored (controlled storage) for a few years and decided to get it home and boot it up.
It starts up with a beep then I can hear disks spinning up, CDROM moving but nothing is displayed on the monitor.
Can... (2 Replies)
Discussion started by: robbo007
2 Replies
LEARN ABOUT DEBIAN
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)