Not showing ifcfg eth0....redhat enterprise Linux 6.2
Hello, I'm using dell inspiron 14R laptop and I installed Redhat enterprise 6.2 on this. After successfully installation i did not found any network interface on this.
when i'm trying to load/add qeth driver . The driver is not found showing this message.
Hi there,
I got a problem with my linux eth0.
It worked well, just one day when i boot it, "Failed" to be active.
The eth0 is inactive! I tried to use KDE network configuration tool to add the type of the eth card, I can't make it active. It gave me warning of "the eth card can't be... (1 Reply)
Hi all,
Thanks for reading and any posts.
Quick question, has anyone out there got any suggestions for standards of security for Redhat enterprise 3. We are making an RAC cluster Oracle application using Oracle 9i (hopefully moving to 10g sooner rather than later).
Thanks again for any... (0 Replies)
when i finish installed rhel 4.4 to my hp dl585 box, ifcfg-eth0 and ifcfg-eth1 is not available.when i ifconfig -a,i can not see the eth0 and eth1, only lo0 and si0. Unlike to the other server i found eth0 and eth1 files in
/etc/sysconfig/network-scripts/.
what will i do? (2 Replies)
Hi All,
I have to upgrade python installed on my Redhat enterprise Linux 4. I downloaded the latest python package from python website but not able to install the new package as the make command itself goes on running for more than a day. Can some help me regarding this. Is ther any method to... (2 Replies)
hi all
do i need to add rc. prefix on the stop script all the time especially on redhat 5 enterprise? like below
ln -s /etc/init.d/rc.stopdb2 /etc/rc0.d/K01rc.stopdb2
and on the /etc/rc.local, i need to add this only
touch /var/lock/subsys/stopdb2
Is that going to work?
thanks... (1 Reply)
When i finished installation the Redhat Enterprise Linux 6.2, and login to the system, I can't login although username: root and Password correct. I install on the Hp Blade Server. I don't know why.
How to fix this error? who can help me? :confused:
Thanks! (3 Replies)
Hi guys,
I really need your help with this.
My network interface eth0 is up but not running. I checked udev rules and ifcfg-eth0 files to make sure the mac address are the same.
It just would not come up. Please please I will really appreciate the help here.
Thank you in advance. (3 Replies)
Having an issue with clustat not displaying the rgmanager info eventhu all the of the cman started successfully. No fencing errors. all of the cluster.conf are the same on all serers ..etc. However when i run the clustat i only see this:
Cluster Status for RESTON-LSMS @ Mon Aug 31 15:13:16 2015... (4 Replies)
Discussion started by: mrn6430
4 Replies
LEARN ABOUT FREEBSD
malo
MALO(4) BSD Kernel Interfaces Manual MALO(4)NAME
malo -- Marvell Libertas IEEE 802.11b/g wireless network driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device malo
device pci
device wlan
device firmware
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_malo_load="YES"
DESCRIPTION
The malo driver provides support for Marvell Libertas 88W8335 based PCI and Cardbus network adapters. malo supports station and monitor mode
operation. Only one virtual interface may be configured at any time. For more information on configuring this device, see ifconfig(8).
This driver requires the malofw firmware kernel module be installed before it will work. The firmware files are not publicly available. A
port of the firmware can be found at:
http://weongyo.org/project/malo/malo-firmware-1.4.tar.gz
The firmware kernel module can be installed by extracting the archive and running 'make install clean' in the malo-firmware-1.4 directory.
To load the malofw firmware kernel module at boot time, place the following line in loader.conf(5):
malofw_load="YES"
HARDWARE
The following cards are among those supported by the malo driver:
Card Chip Bus Standard
Netgear WG311v3 88W8335 PCI b/g
Tenda TWL542P 88W8335 PCI b/g
U-Khan UW-2054i 88W8335 PCI b/g
EXAMPLES
Join an existing BSS network (i.e., connect to an access point):
ifconfig wlan create wlandev malo0 inet 192.168.0.20
netmask 0xffffff00
Join a specific BSS network with network name ``my_net'':
ifconfig wlan create wlandev malo0 ssid my_net up
Join a specific BSS network with 64-bit WEP encryption:
ifconfig wlan create wlandev malo0 ssid my_net
wepmode on wepkey 0x1234567890 weptxkey 1 up
SEE ALSO cardbus(4), pci(4), wlan(4), wlan_ccmp(4), wlan_tkip(4), wlan_wep(4), ifconfig(8), wpa_supplicant(8)HISTORY
The malo device driver first appeared in FreeBSD 7.1.
BSD September 20, 2014 BSD