01-27-2013
Help asap squid with 2 nic cards setup
I found an old post that talks about 2 nice cards and it is driven by the IP address .... but I didn't understand it because the 2 people skipped information for me the newbie..
Can someone help me... I have the proxy server setup and I believe I have enabled the 2nd nic card, I just need one card to take the switch with the other computers and the other to internet.
Thank you
9 More Discussions You Might Find Interesting
1. Solaris
I need to add a PCI NIC to a sunblade 100 running solaris 8. Im new to this and was hoping someone could give me some card names and models which will work for this system and has a driver for this sparc system.
thanks (3 Replies)
Discussion started by: meyersp
3 Replies
2. IP Networking
Hi;
I have a UNIX box (SCO 5.0.2) with two (2) NIC cards. One card (NIC1) talks to a network 57.14.65.x/27. The other card NIC2) talks to users on 57.14.103.x and 57.14.105.x with subnet mask of 255.255.0.0. If I set NIC2 to this subnet mask (255.255.0.0) it seems like the NIC traffic is now... (2 Replies)
Discussion started by: texaspanama
2 Replies
3. High Performance Computing
Hello
I have 2 machines with 3 NIC cards.
When I setup veritas, I receive this message:
e1000g1 has an IP address configured on it. It could be a public NIC on ken.
Are you sure you want to use e1000g1 for the first private heartbeat link?
As if e1000g1 should not have an IP address.... (2 Replies)
Discussion started by: melanie_pfefer
2 Replies
4. HP-UX
I am running HP_UX 11.23 with 4 NIC cards (this is our TSM server)
I have 4 subnets we are backing across. trying to keep traffic on their subnets. I only have one route statment should I add more.
route add net 123.99.8.0 netmask 255.255.255.0 123.99.8.254
route add net 123.99.67.0 netmask... (2 Replies)
Discussion started by: myork
2 Replies
5. Red Hat
We have a setup of two nodes which has two NIC cards in each. One is built in and another is D-Link (external NIC card). We are unable to ping to the external NIC cards in both. Eg: Node A has two IPs 192.168.1.10 (eth0) and 192.168.2.10 (eth1) and Node B has two IPs 192.168.1.20 (eth0) and... (3 Replies)
Discussion started by: durgaprasadr13
3 Replies
6. HP-UX
Hello,
I am trying to move an HP UX from one locaion to another. The new location don't have any Fiber switches.
On the back of my server I see 2 RJ 45 for console management the other for networking , the server also has a fiber NIC card. When I disconnec the fiber and want to user regular... (1 Reply)
Discussion started by: ldaliosmane
1 Replies
7. IP Networking
Hi,
What is the best reference that gives in detail on nic cards configuration , assigning multiple ip addresses to a single interface, netlink library etc and all basic stuff at this level..?
Thanks (2 Replies)
Discussion started by: Gopi Krishna P
2 Replies
8. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
9. Ubuntu
I have a made my squid proxy, I now have add another nic card to an old CPU using Ubuntu server 12.04. I have seen another post similar however I am new and did not understand some of it. Something about redirecting IP address and IP table?
I don't know how to do this.:confused: (9 Replies)
Discussion started by: trilju2005
9 Replies
LEARN ABOUT REDHAT
dummy_cs
DUMMY_CS(4) Kernel Interfaces Manual DUMMY_CS(4)
NAME
dummy_cs - PCMCIA dummy device driver
SYNOPSIS
insmod dummy_cs.o [pc_debug=n] [free_ports=n] [irq_list=i,j,...]
DESCRIPTION
The dummy_cs module has two purposes. It is intended as a demonstration of how to write the PCMCIA interface code for a client driver, and
the source code is heavily commented. It is also written to function as a sort of generic ``point enabler'': when bound to any PCMCIA IO
card, it will read the card's Configuration Information Structure, and configure the card appropriately. The configuration includes set-
ting up IO and memory windows, configuring the card for interrupts, and initializing the card's PCMCIA configuration registers.
It turns out that many cards report incomplete or inaccurate configuration information, due to vendor carelessness and the complexity of
the data format. A vendor driver can generally take for granted many configuration details, so there is not much incentive for vendors to
ensure that the on-card information is complete. Thus, the dummy_cs module is limited by its generality: since it makes no assumptions
about card types, it is forced to rely on the card information, for better or worse.
PARAMETERS
pc_debug=n
Selects the PCMCIA debugging level. This parameter is only available if the module is compiled with debugging enabled. A non-zero
value enables debugging.
free_ports=n
A flag indicating if the IO ports allocated for the card should be freed from the kernel resource maps. This is useful if the dummy
driver is being used to configure a card in preparation for loading a specific PCMCIA-unaware driver. The default is 0 (false).
irq_list=i,j,...
Specifies the set of interrupts that may be allocated by this driver.
AUTHOR
David Hinds - dahinds@users.sourceforge.net
SEE ALSO
cardmgr(8), pcmcia(5).
pcmcia-cs 2000/06/12 21:24:47 DUMMY_CS(4)