Is there any way to do variable nesting using sh?
For example:
example_1="a test string"
example_2="another test"
example_3="etc..."
i=2
echo ${example_$i}
The shell reports:
sh: ${example_$i}: bad substitution
If not, maybe someone could suggest another method. Thanks in... (3 Replies)
I need help getting over this bump on how nested for loops work in shell. Say i was comparing files in a directory in any other language my for loop would look like so
for(int i=0;to then end; i++)
for(int y = i+1; to the end; y++)
I can't seem to understand how i can translate that... (5 Replies)
Greetings All,
The following script attempts to enumerate all users in all groups in the group file(GROUP) and echo the following information:
GROUP ---> USER
The script is as follows:
IFS=","
for GROUP in `ypcat -k group | cut -d" " -f1`
do
for USER in `ypcat -k group... (13 Replies)
Trying to clean up the last little thing in this script which is that the mv always performs no matter whether it is needed or not. It doesn't cause any bugs just prints an unsightly "can't mv source and dest are the same". Obviously I want to get rid of it but having issues getting the... (4 Replies)
Hi there,
I have nested case in my script. I am asking user, want to continue? if user press y/Y then my inner case should continue, rather than that my code start from beginning. I would like to continue my inner case until user press n or N. Is any one tell me how can I do?
Thanking You,... (2 Replies)
Hi,
I have to assign a value for a varaiable based on a Input. I have written the below code:
if
then
nf=65
elif
then
nf=46
elif
then
nf=164
elif
then
nf=545
elif
then
nf=56
elif
then (3 Replies)
Hi Team,
I just want to check whether my nested if loop used is correct or not.
if ]
if ]
export1
else
export2
fi
else
if ]
export3
else
export4
fi
fi
Thanks
Shiva (5 Replies)
HI everyone,
I am not able to find error in the script, when i run the script till
line No. 20
i.e, read var4
everything runs fine. After that the script exits out.
#!/bin/bash
echo -e "Want dryrun OR merge: \n "
read var1
if ] ; then
echo -e "\n Please select from the given... (10 Replies)
Discussion started by: rishi.aradhya
10 Replies
LEARN ABOUT DEBIAN
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)