Hi folks,
I need to find the following value:
First,I need to find the starting section by finding the line:
<process-type id="OC4J_RiGHTv_${SCHEMA_NAME}" module-id="OC4J">
Second,under this line I need to find the following line:
<port id="rmi" range="3765-3776"/>
And third,from this line... (4 Replies)
Hi Everyone, I have an sh script that I am working on and I have run into a little snag that I am hoping someone here can assist me with.
I am using wget to retrieve an xml file from thetvdb.com. This part works ok but what I need to be able to do is extract the series ID # from the xml and put... (10 Replies)
Hi all,
may seem a very stupid question.but me stuck up in it for long....
How to find the number of columns in a ASCII file.
EX:-Demo.lst
songs 1 34 45 67
Number of columns should be 5.
Regards,
Anindya
;) (13 Replies)
This should follow with my last post but I think it's better to start a new one. Now I have a list of numbers stored in pos.txt:
2
6
7
.
.
.
n
.
.
.
And I need to extract (2n-1, 2n) columns from matrix.txt:
ind1 A B C D E F G H I J K L M N O P Q R ...
ind2 B C D E F G H... (3 Replies)
i have a file which may have 'n' number of columns
1 222 fafda 32 afdaf 4343 4343
234 43fdaf 4343 fdd fdfd fdfd fdd fdfd fdfd
fdfd fdfd fdfd fdd fdfd fdfd
need to concatenate the columns with... (3 Replies)
Hi,
I have a data file that contains 61 columns. I want to delete all the columns except columns, 3,6 and 8. The columns are tab de-limited. How would I achieve this on the terminal?
Thanks (2 Replies)
Hi,
I have one input file with the following content:
MY_inpfile.txt
Aname1 Cname1 Cname2 1808 5
Aname2 Cname1 1802 47
Bname1 ? 1819 22
Bname2 Cname1 1784 11
Bname3 1817 9
Zname1 Cname1 1805 59
Zname2 Cname1 Cname2 Cname3 1797 27
Every line in my input file have a 4 digit... (5 Replies)
How to find the number of columns in xml file.
i tried following command.
#!bin/ksh
cat $1 | grep -c "</mdm:attribute>"
exit 0
but i am not getting accurate result which is not matching with the manual count.
data format :
<mdm:attribute> value </mdm:attribute> (6 Replies)
Hi All,
I have more than half million lines of XML file , wanted to split in four files in a such a way that top 7 lines should be present in each file on top and bottom line of should be present in each file at bottom.
from the 8th line actual record starts and each record contains 15 lines... (14 Replies)
Hi All
I have a file which has five columns in each rows.
cat file.txt
a|b|c|d|e
1|2|3|4|5
a1|a2|a3|a4|a5
.
.
.
I need to make sure that there are no less than five or more than five columns (in all the rows) by mistake. I tried this :
cat file.txt | awk 'BEGIN{FS="|"};{print... (3 Replies)
Discussion started by: chatwithsaurav
3 Replies
LEARN ABOUT DEBIAN
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)