12-21-2012
Hi Scott,
I am not aware of command to check the status of loopback service.
Please let me know the command, i will share the results.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi, dear all, I am rather new to Unix and have this problem where I cant seem to ping from 1 host to another. The scenerio is as follows: -
1 QNX host->Eth->1 SCO host
the SCO host is configured with it's IP
the QNX host is configured with another IP
both in the same domain, ie, 172.20.3.XX... (3 Replies)
Discussion started by: gavon
3 Replies
2. UNIX for Dummies Questions & Answers
Hello,
hi guys I don't know what is the problem with my NIC I can ping the Localhost (LOOPBACK) but when I run a scripts to check the NIC statuse it's shown the NIC DOWN sooo what could be the problem and what is the best way to start trouplshooting the NIC in SUN-SOLARIS.
Regards,
Karim
... (3 Replies)
Discussion started by: geoquest
3 Replies
3. UNIX for Dummies Questions & Answers
I have Sco openserver 5.0. It had a 125. ip. I changed it to a 192. ip. was unable to ping the 192. I was told to change it in the
etc/tcp
etc/hosts
files which i did. still unable to ping.
i am getting a message unable to route to host.
I also have an error in my etc/tcp file on line... (1 Reply)
Discussion started by: pdoug76
1 Replies
4. UNIX for Dummies Questions & Answers
DEar all
i am receiving this error on start and then unable to ping
(dlpid): unable to open network adapter driver (/dev/mdi/e3h0)
what to do ? (2 Replies)
Discussion started by: sak900354
2 Replies
5. IP Networking
We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command
64 bytes from 124.168.215.40:... (6 Replies)
Discussion started by: chrisanto_2000
6 Replies
6. Solaris
hi,
I setup a Solaris machine in my server room and my client cannot access it. Can anyone advise?
Test that i have done:
-My client pc cannot ping the server.
-My solaris server cannot ping client
-My solaris server can ping it's gateway
-Another NT machine 1 (10.179.30.26) in the server... (2 Replies)
Discussion started by: skiturn
2 Replies
7. IP Networking
hi,
I setup a Solaris machine in my server room and my client cannot access it. Can anyone advise?
Test that i have done:
-My client pc cannot ping the server.
-My solaris server cannot ping client
-My solaris server can ping it's gateway
-Another NT machine 1 (10.179.30.26) in the... (8 Replies)
Discussion started by: skiturn
8 Replies
8. Solaris
Hi ALL,
I Have installed NEW v240 server through hyper terminal, After installation i unable to ping the server from out side server... i can see no entry in resolve.conf file.. but the server has DNS.. willl that issue.. please guide me ping the server from outside within the same network
bk (1 Reply)
Discussion started by: suresh_krish
1 Replies
9. Solaris
Hello,
Am unable to ping the Windows Box, from my Solaris Box.
They both are in same LAN, have the same IP Segments.
Windows IP :: 10.141.14.120
Solaris IP :: 10.141.14.11
Unable to get why isnt working out.... When using the command 'ping 10.141.14.120', it gives the error as 'ping:... (4 Replies)
Discussion started by: jayanto
4 Replies
10. IP Networking
Hello Everyone,
I have unable to run the default server with localhost in my Debian machine. While trying to run Django I get:
Error: That IP address can't be assigned-to.
error
While trying to run galaxy-dist I get this error:
socket.error: Cannot assign requested address
I can't telnet... (3 Replies)
Discussion started by: sachit adhikari
3 Replies
LEARN ABOUT DEBIAN
update-service
update-service(8) System Manager's Manual update-service(8)
NAME
update-service - add/remove a service to/from system-wide service supervision
SYNOPSIS
update-service --add|--remove service-directory [service-name]
update-service --list|--check [service-name]
DESCRIPTION
service-directory must be a directory to be used by supervise(8), service-name must not start with a dot, and must not contain a slash.
update-service adds or removes the service-directory to the system-wide service supervision provided through daemontools' svscan(8), lists
all registered system-wide services, or checks for a specific service-name whether it is registered.
When adding a service, and the service-directory resides in /etc/, update-service makes sure that the ./supervise/ subdirectories in the
service-directory, and the optional service-directory/log/, are symbolic links pointing into /var/lib/supervise/, unless they already are
symbolic links.
OPTIONS
--add | -a
Add the service directory service-directory to the system-wide service supervision, under the name service-name. If service-name is
not specified, update-service will use the basename of service-directory. You can use the svc(8) program to control the newly added
service, and the svstat(8) program to query its status, e.g.:
# svstat /etc/service/service-name
--remove | -r
Remove the service directory service-directory, which has been added under the name service-name, from the system-wide service
supervision. If service-name is not specified, update-service will use the basename of service-directory. When removing the ser-
vice-directory, the exit command is sent to the corresponding supervise(8) process, telling it to take the service down and exit
afterwards. You can use the svc(8) and svstat(8) programs to control the removed service, or query its status, e.g.:
# svstat service-directory
--list | -l
If service-name is specified, update-service checks whether service-name is registered as system-wide service, prints a message and
exits non-zero if not, or prints the service-name and the directory it points to and exits zero if yes. If service-name is not
specified, it prints the names of all system-widely registered services, one per line.
--check | -c
The same as --list, but update-service doesn't print anything to standard out or standard error.
ENVIRONMENT
SVDIR The environment variable $SVDIR overrides the default services directory /etc/service/.
FILES
/etc/service/
SEE ALSO
svc(8), svstat(8), svscan(8), svscanboot(8)
AUTHOR
Gerrit Pape <pape@smarden.org>
update-service(8)