Dear Guyz:)
I have 2 different input files like this. I would like to pick the values or letters from the inputfile2 based on inputfile1 keys (A,F,N,X,Z).
I have done similar task by using awk but in that case the inputfiles are similar like in inputfile2 (all keys in 1st column and values in... (16 Replies)
awk '{ gsub(/....=/,""); print }' want.dat >final.dat
the above awk command which removes all the chars before and including '=' on the entire row. --thats what it meant be.:)
but i need to remove text on column-wise on each row.
many thanks,
EM
---------- Post updated at 10:00 AM... (4 Replies)
Hello,
I have 2 columns (1st column has multiple entries but the corresponding values in the column 2 may be the same or different.) however I want to extract unique values for each entry in column 1 by assigning the max value from column 2
SDF4 -0.211654
SDF4 0.978068
... (1 Reply)
Can somebody help me out and provide me with a SED or AWK solution that converts TO_DATE CLAUSE -> TIMESTAMP
I need to keep the PARTION value (HISTORY_20110417) and DATE/TIME value (2011-04-18 00:00:00) the same for every line
PARTITION HISTORY_20110417 VALUES LESS THAN (TO_DATE('... (3 Replies)
Hi all.
I have the following command that is successfully searching for any one of the strings on all lines of a file and replacing it with the instructed value.
cat inputFile | awk '{gsub(/aaa|bbb|ccc|ddd/,"1234")}1' > outputFile
This does in fact replace any occurrence of aaa, bbb,... (2 Replies)
Hi,
I have a tab delimited text file with two columns where the second column takes on values between 1 and 6 (including). If the value of the second column, includes 1,2,3 I want to replace it with LOW. If it is 4,5,6 I want to replace it with HIGH. How do I go about doing that? Thanks
... (3 Replies)
I have a file which looks like this:
1 3 5 5 3 2
1 5 3 6 3 2
0 5 6 3 2 9
0 4 5 6 4 9
In the first column, instead of 1, I want to place +1 and instead of 0, I want -1 to be put. So the generated file should look like this:
+1 3 5 5 3 2
+1 5 3 6 3 2
-1 5 6 3 2 9
-1 4 5 6 4 9
Just to... (9 Replies)
My program run without error. The problem I am having.
The program isn't outputting field values with the column headers to file.txt.
Each of the column headers in file.txt has no data.
MEMSIZE SECOND SASFoundation Filename
The output results in file.txt should show:
... (1 Reply)
Please help me to get required output for both scenario 1 and scenario 2 and need separate code for both scenario 1 and scenario 2
Scenario 1
i need to do below changes only when column1 is CR and column3 has duplicates rows/values. This inputfile can contain 100 of this duplicated rows of... (1 Reply)
Discussion started by: as7951
1 Replies
LEARN ABOUT DEBIAN
text2ps
TEXT2PS(L) TEXT2PS(L)
NAME
text2ps - convert text files to PostScript
SYNOPSIS
text2ps [ options ] [ files ]
DESCRIPTION
Text2ps reads the input files (standard input if none are specified) and produces PostScript code which, when fed to a PostScript printer,
will print the files. With text2ps it is possible to select any font, point size and number of columns. Options and files can be inter-
mixed on the command line. Options are effective for all following files until they are overridden.
Options
Here follows a list of options that text2ps recognizes. Most numeric arguments are significant to one decimal place. Options are evalu-
ated from left to right. Later options override earlier ones.
-# n Print n copies of each page. (Default 1.)
-c n Print in n columns. (Default 1.)
-f font
Print using font font. (Default Courier.)
-p n Print with point size n. (Default 9.)
-v n Use a vertical spacing of n points. If the vertical spacing is set to 0, the spacing will be 1.2 times the point size. (Default
0.)
-l n Print n lines per column. When the line count is 0, print as many lines as will fit. (Default 0.)
-r [p|l]
Set the orientation to either portrait mode (p) or landscape mode (l). (Default p.)
-b [+|-]
Set page break mode. An argument + will force new files to be always printed on a new page (this is the default). After - new
files will be put on the same page if there are still empty columns and the number of columns, the orientation or the number of
copies didn't change. New files always start new columns. (Default -.)
-mt n The top margin is n points. (Default 63.)
-mb n The bottom margin is n points. (Default 63.)
-ml n The left margin is n points. (Default 59.)
-mr n The right margin is n points. (Default 59.)
-mg n The inter-column gap is n points. (Default 25.)
-t [+|-]
If the argument is + the name of the file being printed will be printed on each page. If the argument is - the file name will not
be printed. -t + implies -b +.
-T text
Print text as title on each page. This implies -t - and -b +. This option can be switched off by specifying -t - or -t +.
(Default no title.)
-F font
Set the title font to font. (Default Helvetica.)
-P n Set the title point size to n. (Default 12.)
-B n Draw borders around each page. The number n specifies how to draw borders. N can have any of the following values or-ed in:
1 Draw a line along the left of the page.
2 Draw a line along the bottom of the page.
4 Draw a line along the right of the page.
8 Draw a line along the top of the page.
16 Draw a line between columns. This line does not connect to the lines along the top or bottom.
32 Draw a connecting line between the line between columns and the line along the top.
64 Draw a connecting line between the line between columns and the line along the bottom.
When n is 0, no border lines are drawn. (Default no bordering lines.)
-w n Tab stops are set every n spaces. Set the width of the TAB character. (Default 8.)
-1 Sets up options to print in one column in portrait mode with the Courier font, so that you get 66 lines on a page. Equivalent to
specifying the options -c 1 -f Courier -p 9 -v 0 -r p -l 0 -mt 63 -mb 63 -ml 59 -mr 59.
This is the default.
-2 Sets up options to print in two columns in landscape mode with the Courier font, so that you get two 66-line columns on a page.
Equivalent to specifying the options -c 2 -f Courier -p 6 -v 0 -r l -l 0 -mt 63 -mb 63 -ml 59 -mr 59 -mg 25. Together with the -1
option, this is probably the most useful option.
The name - means standard input.
BUGS
Too many options.
There is no way to specify where the title will be placed.
If the font being used is not a constant width font and there are other characters than just tabs and spaces in front of a tab, the next
character may not align properly.
TEXT2PS(L)