Hi
I want to read a flat file and add a word/value at the end of each line in the file and store the output in a temporary file. How can i do this? Plz help me with this.
Regards,
Saurabh (6 Replies)
Hi,
Can anybody help me how to add a word in front of a line in a file.Actually it is bit tricky to add a word. i will give a sample for this:
Input :
1110001 ABC DEF
1110001 EFG HIJ
1110001 KLM NOP
1110002 QRS RST
1110002 UVW XYZ
Output:
%HD% 1110001 ABC DEF
%DT% 1110001 EFG HIJ... (4 Replies)
I have a file which will have rows like shown below,
ST*820*316054716
RMR*IV*11333331009*PO*40.31
REF*IV*22234441009*xsss471-2762
DTM*003*091016
ENT*000006
RMR*IV*2222234444*PO*239.91
REF*IV*1234445451009*LJhjlkhkj471-2762 </SPAN>
DTM*003*
091016
RMR*IV*2223344441009*PO*40.31... (18 Replies)
hey,
i would like to add a line number to the beginning like so:
red
blue
green
yellow
will be:
1=>red
2=>blue
3=>green
4=>yellowplease advise
thank u. (5 Replies)
Well here goes:
I tried to write a batch file that adds a specific fixed text to each line of an already existing text file.
for the adding text infront of each line I tried this:
for /F "delims=" %%j in (list.txt) do echo.STARTTEXT\%%j >> list.txt
for adding text after each line I... (6 Replies)
Hi,
I have a specific requirement to add text at the beginning and end of a plain text file. I tried to use "sed" with '1i' and '$a' flags but these required two separate "sed" commands separated with "|".
I am looking for some command/option to join these two in single command parameter.
... (6 Replies)
My file has the entries like below...
/dev/sds
/dev/sdak
/dev/sdbc
/dev/sdbu
I want to make the file like below
echo 1 > /sys/block/sds/device/rescan
echo 1 > /sys/block/sdak/device/rescan
echo 1 > /sys/block/sdbc/device/rescan
echo 1 > /sys/block/sdbu/device/rescan (2 Replies)
SUSE linux
bash shell
this works
test -d /tmpp && echo "directory exists" || echo "directory doesn't exists" |sed -e "s/^/prefix /"
prefix directory doesn't exists
but why doesn't this work?
test -d /tmp && echo "directory exists" || echo "directory doesn't exists" |sed -e... (3 Replies)
Discussion started by: snoman1
3 Replies
LEARN ABOUT LINUX
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)