11-29-2012
I have seen this happen before (but not on a V240).
Oracle/Sun don't seem to warn you most of the time that an out of date OBP/hypervisor, etc can cause a crash/hang during application of a patchset.
If you need to crash the system (STOP-A) and reset, followed by normal fsck, etc, you could then run the whole patchset again. It will 'skip' the patches already applied.
If it crashes/hangs again then you need to look at OBP versions, etc.
Here's an earlier thread...............
t2000 Sol10 installation failure
10 More Discussions You Might Find Interesting
1. IP Networking
I installed sco unix v 5.0.5 in the hp server lc 2000 HD size
27gb & ram 256 , used micro focus cobol for unix , aplication
system bank , the problem is the system hung 2 or 3 times a day
will you pls. give me the solution.
thanks
talib alsaadi
:( (2 Replies)
Discussion started by: talib alsaadi
2 Replies
2. UNIX for Dummies Questions & Answers
Anyone have any ideas what could be causing me to get the error "The SCSI bus is hung. Perhaps an external device is turned off"? This is occuring when I try to boot off of my external CDROM. I have tried this CDROM on 3 different systems, tried different SCSI cables, and different terminators... (2 Replies)
Discussion started by: saucierm
2 Replies
3. Solaris
What do you do if the system will not respond to commands? I'm using SUN Fire v210. We had a power hit, so i think it caused a problem. The monitor does not come up anymore. So i plugged in on a laptop via serial port, rebooted. The system seems to start to boot, but comes up to message "SC... (11 Replies)
Discussion started by: ireeneek
11 Replies
4. HP-UX
So my server was hung when I came in this morning. It was responding to pings, but the console and telnet sessions would not respond. There was no disk activity. The display said FA1F which I discovered that the "A" represents a high CPU load. I tired several things to get it going but was forced... (6 Replies)
Discussion started by: biznatch
6 Replies
5. HP-UX
Here's a difficult one for you.
I am on HPUX 11.0. I have a hung port, it is stuck in FIN_WAIT_2. Short of rebooting, how can I terminate the connection the system thinks still exists? I found a script online that uses adb but have not been able to get it to work. I am still open to using... (6 Replies)
Discussion started by: TioTony
6 Replies
6. Programming
Hi friends
I am Administrator for a system works with uinx OS but, many times I get messages from server console inform me about Subroutine is Hanging
so what can I do to reset this Subroutine?
Note: always when I got that I restart the server but I think that is not professional solution. (3 Replies)
Discussion started by: bintaleb
3 Replies
7. UNIX for Advanced & Expert Users
We are using software (Pegasys) which runs on SunOS 5.8 and reads images from a Philips nuclear camera. The software is designed to run from the console. I need to be able to capture the images it produces on the display. The caveat is that I cannot use the X Windows display because the X Server... (3 Replies)
Discussion started by: sreyes27
3 Replies
8. HP-UX
Our network administrators implemented some sort of check to kill idle sessions and now burden is on us to run some sort of keep alive. Client based keep alive doesn't do a very good job. I have same issue with ssh. Does solution 2 provided above apply for ssh sessions also? (1 Reply)
Discussion started by: yoda9691
1 Replies
9. UNIX for Dummies Questions & Answers
:confused:Hi
This was installed on the Linux box a few weeks back by a guy that no longer works for us. All worked fine until last week. Now when we connect its just a blank screen with no icons.
I get a whole bunch of errors when starting the service too:
Tue Feb 23 14:29:45 2010
... (1 Reply)
Discussion started by: wbdevilliers
1 Replies
10. Solaris
While trying to perform a firmware upgrade on this ilom, the system refused to allow uploading of more than ~900k or so... We tried multiple approaches using FTP and all failed. I decided to start this morning by firing up Apache on another box and trying the same process via HTTP but when I went... (8 Replies)
Discussion started by: DustinT
8 Replies
LEARN ABOUT OSX
git-quiltimport
GIT-QUILTIMPORT(1) Git Manual GIT-QUILTIMPORT(1)
NAME
git-quiltimport - Applies a quilt patchset onto the current branch
SYNOPSIS
git quiltimport [--dry-run | -n] [--author <author>] [--patches <dir>]
[--series <file>]
DESCRIPTION
Applies a quilt patchset onto the current Git branch, preserving the patch boundaries, patch order, and patch descriptions present in the
quilt patchset.
For each patch the code attempts to extract the author from the patch description. If that fails it falls back to the author specified with
--author. If the --author flag was not given the patch description is displayed and the user is asked to interactively enter the author of
the patch.
If a subject is not found in the patch description the patch name is preserved as the 1 line subject in the Git description.
OPTIONS
-n, --dry-run
Walk through the patches in the series and warn if we cannot find all of the necessary information to commit a patch. At the time of
this writing only missing author information is warned about.
--author Author Name <Author Email>
The author name and email address to use when no author information can be found in the patch description.
--patches <dir>
The directory to find the quilt patches.
The default for the patch directory is patches or the value of the $QUILT_PATCHES environment variable.
--series <file>
The quilt series file.
The default for the series file is <patches>/series or the value of the $QUILT_SERIES environment variable.
GIT
Part of the git(1) suite
Git 2.17.1 10/05/2018 GIT-QUILTIMPORT(1)