I have two disks on a sun blade 100. I just installed a solaris8 on the first disk. The installation was successful. But the problem is now I lost all data / partition on my second hard disk.
The possible reason could be:
1. I used default web start install. During the installation I didn't... (2 Replies)
Hello everyone -
Please forgive me if I violate the forum's etiquette as this is my very first post. I'm posting this on both the dummies and the advance section with the hope for any responses.
I stumbled on this forum while frantically looking for an answer to a dumb, ignorant thing I did... (2 Replies)
Hello everyone -
Please forgive me if I violate the forum's etiquette as this is my very first post. I'm posting this on both the dummies and the advance section with the hope for any responses.
I stumbled on this forum while frantically looking for an answer to a dumb, ignorant thing I did... (5 Replies)
Q. Write a script that behaves both in interactive and non interactive mode. When no arguments are supplied it picks up each C program from the directory and prints first 10 lines.
It then prompts for deletion of the file.
If user supplies arguments with the script , then it works on those files... (1 Reply)
Q. Write a script that behaves both in interactive and non interactive mode. When no arguments are supplied it picks up each C program from the directory and prints first 10 lines.
It then prompts for deletion of the file.
If user supplies arguments with the script , then it works on those files... (8 Replies)
I'm using
fdisk -l > myFile
to get the file size of the device in a file where I want the output
but one line always go to the terminal and make my interface look ugly:
Disk /dev/sda doesn't contain a valid partition table
How do I stop this line from going to the command line with a... (2 Replies)
Hello,
I have a RHEL system with two 500GB hard drives in RAID 1 (I think hardware, but not 100% certain - any way to tell?).
It looks like it was just set up in default configuration with a small boot partition and one huge partition for the rest, which composes a LVM volume.
I want... (1 Reply)
Hello,
I have been going through our environment and I see we have a few servers with LVM's setup and the file system type is still set to "83" within fdisk. If I change this to "8e", will it hurt the data or cause any loss? I need to know for sure before I make the change. (1 Reply)
Hello,
MBR partition table made by linux fdisk looks certainly not correct when printed by openbsd fdisk:
Partition table created on linux (centos 6.3):
# fdisk -l /dev/sdc
Disk /dev/sdc: 10.7 GB, 10737418240 bytes
255 heads, 63 sectors/track, 1305 cylinders
Units = cylinders of 16065 *... (2 Replies)
Discussion started by: vilius
2 Replies
LEARN ABOUT XFREE86
partx
PARTX(8) System Administration PARTX(8)NAME
partx - tell the kernel about the presence and numbering of on-disk partitions
SYNOPSIS
partx [-a|-d|-P|-r|-s|-u] [-t type] [-n M:N] [-] disk
partx [-a|-d|-P|-r|-s|-u] [-t type] partition [disk]
DESCRIPTION
Given a device or disk-image, partx tries to parse the partition table and list its contents. It can also tell the kernel to add or remove
partitions from its bookkeeping.
The disk argument is optional when a partition argument is provided. To force scanning a partition as if it were a whole disk (for example
to list nested subpartitions), use the argument "-" (hyphen-minus). For example:
partx --show - /dev/sda3
This will see sda3 as a whole-disk rather than as a partition.
partx is not an fdisk program - adding and removing partitions does not change the disk, it just tells the kernel about the presence and
numbering of on-disk partitions.
OPTIONS-a, --add
Add the specified partitions, or read the disk and add all partitions.
-b, --bytes
Print the SIZE column in bytes rather than in human-readable format.
-d, --delete
Delete the specified partitions or all partitions.
-g, --noheadings
Do not print a header line with --show or --raw.
-l, --list
List the partitions. Note that all numbers are in 512-byte sectors. This output format is DEPRECATED in favour of --show. Do not
use it in newly written scripts.
-n, --nr M:N
Specify the range of partitions. For backward compatibility also the format M-N is supported. The range may contain negative num-
bers, for example --nr -1:-1 means the last partition, and --nr -2:-1 means the last two partitions. Supported range specifications
are:
M Specifies just one partition (e.g. --nr 3).
M: Specifies the lower limit only (e.g. --nr 2:).
:N Specifies the upper limit only (e.g. --nr :4).
M:N Specifies the lower and upper limits (e.g. --nr 2:4).
-o, --output list
Define the output columns to use for --show, --pairs and --raw output. If no output arrangement is specified, then a default set is
used. Use --help to get list of all supported columns. This option cannot be combined with the --add, --delete, --update or --list
options.
-P, --pairs
List the partitions using the KEY="value" format.
-r, --raw
List the partitions using the raw output format.
-s, --show
List the partitions. The output columns can be selected and rearranged with the --output option. All numbers (except SIZE) are in
512-byte sectors.
-t, --type type
Specify the partition table type.
--list-types
List supported partition types and exit.
-u, --update
Update the specified partitions.
-S, --sector-size size
Overwrite default sector size.
-v, --verbose
Verbose mode.
-V, --version
Display version information and exit.
-h, --help
Display help text and exit.
EXAMPLES
partx --show /dev/sdb3
partx --show --nr 3 /dev/sdb
partx --show /dev/sdb3 /dev/sdb
All three commands list partition 3 of /dev/sdb.
partx --show - /dev/sdb3
Lists all subpartitions on /dev/sdb3 (the device is used as whole-disk).
partx -o START -g --nr 5 /dev/sdb
Prints the start sector of partition 5 on /dev/sdb without header.
partx -o SECTORS,SIZE /dev/sda5 /dev/sda
Lists the length in sectors and human-readable size of partition 5 on /dev/sda.
partx --add --nr 3:5 /dev/sdd
Adds all available partitions from 3 to 5 (inclusive) on /dev/sdd.
partx -d --nr :-1 /dev/sdd
Removes the last partition on /dev/sdd.
SEE ALSOaddpart(8), delpart(8), fdisk(8), parted(8), partprobe(8)AUTHORS
Davidlohr Bueso <dave@gnu.org>
Karel Zak <kzak@redhat.com>
The original version was written by Andries E. Brouwer <aeb@cwi.nl>.
ENVIRONMENT
LIBBLKID_DEBUG=all
enables libblkid debug output.
AVAILABILITY
The partx command is part of the util-linux package and is available from Linux Kernel Archive <https://www.kernel.org/pub/linux/utils
/util-linux/>.
util-linux December 2014 PARTX(8)