Hello
I am a noobie to HACMP
I have 2 55A servers and a 7031 disk subsystem
For HACMP to work, do I need to have the hdisks on both servers to match the same drives??
The hdisks on each box are currently different:
hdisk0 and hdisk1 are the internal disks and hdisk2-5 are on the D24 on... (1 Reply)
I would like to extend a logical drive on our 3510. I have four unallocated disks which I would like to use for this purpose.
The 3510 supports a Sun Cluster but for now all I wish to see is a "new" disk when I run format.
I am a little familiar with the telnet/ssh session on the 3510 but am... (2 Replies)
Hello,
This morning we have added 6 new disks (73 Gb) to our DS4300, then created a new Array en then created a logical drive, after this was done, teh following error occourd on the last 3 (new)disks:
Date/Time: 22-4-08 6:56:26
Sequence number: 5472
Event type: 282D
Event category:... (1 Reply)
Hi,
Can anybody advice whether it is possible to configure HACMP in HP-UX Server.
To my knowledge HACMP is IBM Solution.
Thanks && Regards,
N. Poorna Chandra Rao. (2 Replies)
Hi all,
I have an HACMP (v5.3.0.0) cluster vg attached to ibm shark that need to be decommissioned. The data need to move to the HP EVA disk. The OS is on AIX 5200-10. The plan is to add a new disk from EVA & mirror the existing vg & break the mirror from Shark disk once the mirror finished.
... (12 Replies)
I need some help with adding lines to file and substitute a pattern.
Ok I have a file:
#cat names.txt
name: John Doe
stationed: 1
name: Michael Sweets
stationed: 41
.
.
.
And would like to change it to:
name: John Doe
employed
permanently
stationed: 1-office (7 Replies)
hi,
when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is... (4 Replies)
Hi,
I have a 2 node Cluster. Which is working in active/passive mode (i.e Node#1 is running and when it goes down the Node#2 takes over)
Now there's this requirement that we need a mount point say /test that should be available in active node #1 and when node #1 goes down and node#2 takes... (6 Replies)
Previous forum threads have noted that AIX cannot use iSCSI disks because it fails when trying to add them to a volume group using mkvg. The failure is caused by AIX's use of the SCSI "WRITE AND VERIFY"(0x2e) command which some iSCSI targets do not support.
We experienced the same problem using... (1 Reply)
I have an array in an external file, "array.txt", which contains:
char *testarray={"Zero", "One", "Two", "Three", "Four", "Five", "Six", "Seven", "Eight", "Nine"};I want to be able to add an element to this array, and have that element display, whenever I call it, without having to recompile... (29 Replies)
Discussion started by: ignatius
29 Replies
LEARN ABOUT PHP
vgimportclone
VGIMPORTCLONE(8) System Manager's Manual VGIMPORTCLONE(8)NAME
vgimportclone - import and rename duplicated volume group (e.g. a hardware snapshot)
SYNOPSIS
vgimportclone [-n|--basevgname VolumeGroupName] [-i|--import] PhysicalVolume [PhysicalVolume...]
DESCRIPTION
vgimportclone is used to import a duplicated VG (e.g. hardware snapshot). Duplicate VG(s) and PV(s) are not able to be used until they are
made to coexist with the origin VG(s) and PV(s). vgimportclone renames the VG associated with the specified PV(s) and changes the associ-
ated VG and PV UUIDs.
OPTIONS
See lvm for common options.
-n|--basevgname VolumeGroupName
By default the snapshot VG will be renamed to the original name plus a numeric suffix to avoid duplicate naming (e.g. 'test_vg'
would be renamed to 'test_vg1'). This option will override the base VG name that is used for all VG renames. If a VG already
exists with the specified name a numeric suffix will be added (like the previous example) to make it unique.
-i|--import
Import exported Volume Groups. Otherwise VGs that have been exported will not be changed (nor will their associated PVs).
ENVIRONMENT VARIABLES
LVM_BINARY
The LVM2 binary to use. Defaults to "lvm".
EXAMPLES
The origin VG vg00 has origin PVs /dev/sda and /dev/sdb and the respective snapshot PVs are /dev/sdc and /dev/sdd. To rename the VG asso-
ciated with /dev/sdc and /dev/sdd from vg00 to vg00_snap (and to change associated VG and PV UUIDs) do:
vgimportclone --basevgname vg00_snap /dev/sdc /dev/sdd
SEE ALSO lvm(8)Red Hat, Inc. LVM TOOLS 2.02.95(2) (2012-03-06) VGIMPORTCLONE(8)