I have been able generate a file ($ELOG) that can have multiple lines within it. The first column represents the full path source file and the other is the full path target ... the file names are the same but the target directory paths are slightly different.
I need to run a 3rd party ENCRYPT (executable file) against <source_dir1>/file1 and then move it to <target_dir1/file1...<target_dir1>/file1 is the encrypted version of the human-readable <source_dir1>/file1
The code I have thusfar is
By using basename, I am hoping to seperate the filename so the line should read
ENCRYPT file1 <password> ....pause 3 and then move the file to the correct <target_dir> located in column 2 of the file
Unfortunately the baseline part is not working - what am I not doing correctly ?
The Web-based contact form on my site has been under distributed spamming attacks for nearly a month already. Obviously, a spammer has tried to generate HTTP requests containing ads to male drugs and all sorts of similar stuff directly to the form mail processor script on my site using a robot, as... (5 Replies)
Hi,
I am using the following command to extract any log files that are older than 3 days using the following command.
find DIR/LOGDIR -type f -mtime +3 |grep LOG > log_list.out
The results are
DIR/LOGDIR/1.LOG
DIR/LOGDIR/2.LOG
DIR/LOGDIR/3.LOG
DIR/LOGDIR/4.LOG
How do inculde (basename... (4 Replies)
hi if we have to use basename how can we do this in awk?
did the below but is not working..
psg -t "?"| awk '{
command=($5 ~ /^/)? $9:$8
# cmd_name=`basename $command` (gives error)
system("basename $command >>... (10 Replies)
Hi Experts,
I am adding a column of numbers with awk , however not getting correct output:
# awk '{sum+=$1} END {print sum}' datafile
2.15291e+06
How can I getthe output like : 2152910
Thank you..
# awk '{sum+=$1} END {print sum}' datafile
2.15079e+06 (3 Replies)
I am having a hard time extracting the file name from the above code. Instead of printing /folder/file.1$.5$, I would like it to print the file name file.1$.5$.
I have tried using basename but it looks like NAWK or AWK does not recognise basename. Each time I type it in, it prints out the word... (4 Replies)
Hi gurus,
i need your advise on how to process this file using awk.
i have this file
COLA COLB COLC COLD COLE COLF COLG COLH
AAAA 86 111 122 133 144 155 266 377
BBBB 70 211 222 233 244 255 266 ... (6 Replies)
im trying to extract the basename of a process running on a host
processx is running at host1 as /applications/myapps/bin/processx
i wanted to check if its running, then extract the basename only using:
$ ssh host1 "ps aux | grep -v 'grep' | grep 'processx'" | awk '{ print basename $11}'
... (10 Replies)
Here is a very simple Korn shell script running on an AIX 5.3 box.
Why does this work without the $ prepended to RET_CD?
#!/bin/ksh
RET_CD=0
if &&
then
echo "RET_CD is not 0 and not 2"
else
echo "RET_CD is a 0 or a 2"
fi (3 Replies)
I'm using solaris 10
Scenario as follows
I have a logfile with 2 columns:
column 1 = source directory + filename
column 2 = destination directory + filename
Using cron, my script polls for new files and adds them to the logfile ($ELOG) as described above. Using sed, the distination... (2 Replies)
Hi Guru's.
I am trying to use to check if $5 is greater than 80 & if not 100, then to print $0 :
awk '{ if ($5>80) && if ($5 != 100) print $0}
But getting error:
>bdf1|sed 's/%//g'|awk '{ if ($5>80) && if ($5 != 100) print $0}'
syntax error The source line is 1.
The error... (6 Replies)
Discussion started by: rveri
6 Replies
LEARN ABOUT LINUX
merge
MERGE(1) General Commands Manual MERGE(1)NAME
merge - three-way file merge
SYNOPSIS
merge [ options ] file1 file2 file3
DESCRIPTION
merge incorporates all changes that lead from file2 to file3 into file1. The result ordinarily goes into file1. merge is useful for com-
bining separate changes to an original. Suppose file2 is the original, and both file1 and file3 are modifications of file2. Then merge
combines both changes.
A conflict occurs if both file1 and file3 have changes in a common segment of lines. If a conflict is found, merge normally outputs a
warning and brackets the conflict with <<<<<<< and >>>>>>> lines. A typical conflict will look like this:
<<<<<<< file A
lines in file A
=======
lines in file B
>>>>>>> file B
If there are conflicts, the user should edit the result and delete one of the alternatives.
OPTIONS -A Output conflicts using the -A style of diff3(1), if supported by diff3. This merges all changes leading from file2 to file3 into
file1, and generates the most verbose output.
-E, -e These options specify conflict styles that generate less information than -A. See diff3(1) for details. The default is -E. With
-e, merge does not warn about conflicts.
-L label
This option may be given up to three times, and specifies labels to be used in place of the corresponding file names in conflict
reports. That is, merge -L x -L y -L z a b c generates output that looks like it came from files x, y and z instead of from files
a, b and c.
-p Send results to standard output instead of overwriting file1.
-q Quiet; do not warn about conflicts.
-V Print RCS's version number.
DIAGNOSTICS
Exit status is 0 for no conflicts, 1 for some conflicts, 2 for trouble.
IDENTIFICATION
Author: Walter F. Tichy.
Manual Page Revision: 5.8.1; Release Date: 2012-06-06.
Copyright (C) 2010-2012 Thien-Thi Nguyen.
Copyright (C) 1990, 1991, 1992, 1993, 1994, 1995 Paul Eggert.
Copyright (C) 1982, 1988, 1989 Walter F. Tichy.
SEE ALSO diff3(1), diff(1), rcsmerge(1), co(1).
BUGS
It normally does not make sense to merge binary files as if they were text, but merge tries to do it anyway.
GNU RCS 5.8.1 2012-06-06 MERGE(1)