Hi,
I have a script that runs a process at the beginning and I want to sleep/wait until this process is finished and then continue with the rest of the script. I am trying with this, but it is not working:
Actually, it never ends. Can you help me, please?
If I want a script to sleep for less than a second, would I use a decimal? In other words, if I wanted my script to sleep for 1/4 of a second, would I say, SLEEP .25 ?? (5 Replies)
Does anyone know a way to sleep less than 1 second?
Sometimes when I write scripts that iterates a loop many times it would be
nice to slow things down, but sometimes 1 second is too much. (9 Replies)
I have a function that quits a program when <ctrl>c is entered as per following code;
void quitter (void)
{
clear ();
mvprintw (QUITTER_ROW, QUITTER_COL, "Quitting...");
refresh ();
sleep (15);
endwin ();
exit (1);
}This function is called thus;
signal (SIGINT, quitter);
It... (2 Replies)
I am in need of some help; think I have confused myself.
Here is the issue I am faced with.
The script log file was fine, the nohup.out file has tens of thousands of lines like illegal use of sleep: sleep seconds
So I assume there is something with the seconds calculation in the script... (1 Reply)
Hi All I have a requiremnt to run a script inside another script.
here i am pulling the record count from the table in oracle.If record count is greater than 0 the script is executed.The scripts updates the count in the table and again the count is found out and the condition is checked and same... (3 Replies)
This is a very crude attempt in Bash at something that I needed but didn't seem to find in the 'sleep' command. However, I would like to be able to do it without the need for the temp file. Please go easy on me if this is already possible in some other way:
How many times have you used the... (5 Replies)
This might be one of the dumbest questions you've got, but please bear with me:
I am a UNIX beginner. I had an test today and I was asked the following question:
Q. How do you put the terminal into sleep indefinitely?
I didn't know the answer, but after I came home, I tried the following... (9 Replies)
Hi,
I am a newbie in UNIX
please help me develop code for below logic:--
I want my script to implement sleep until a specified time(date doesn't matter)
----------------------------------------
While currenttime > 14:00 and < 18:00
sleep
end while
run command
exit... (9 Replies)
Discussion started by: kiitmale
9 Replies
LEARN ABOUT DEBIAN
expect_unbuffer
UNBUFFER(1) General Commands Manual UNBUFFER(1)NAME
unbuffer - unbuffer output
SYNOPSIS
unbuffer program [ args ]
INTRODUCTION
unbuffer disables the output buffering that occurs when program output is redirected from non-interactive programs. For example, suppose
you are watching the output from a fifo by running it through od and then more.
od -c /tmp/fifo | more
You will not see anything until a full page of output has been produced.
You can disable this automatic buffering as follows:
unbuffer od -c /tmp/fifo | more
Normally, unbuffer does not read from stdin. This simplifies use of unbuffer in some situations. To use unbuffer in a pipeline, use the
-p flag. Example:
process1 | unbuffer -p process2 | process3
CAVEATS
unbuffer -p may appear to work incorrectly if a process feeding input to unbuffer exits. Consider:
process1 | unbuffer -p process2 | process3
If process1 exits, process2 may not yet have finished. It is impossible for unbuffer to know long to wait for process2 and process2 may
not ever finish, for example, if it is a filter. For expediency, unbuffer simply exits when it encounters an EOF from either its input or
process2.
In order to have a version of unbuffer that worked in all situations, an oracle would be necessary. If you want an application-specific
solution, workarounds or hand-coded Expect may be more suitable. For example, the following example shows how to allow grep to finish pro-
cessing when the cat before it finishes first. Using cat to feed grep would never require unbuffer in real life. It is merely a place-
holder for some imaginary process that may or may not finish. Similarly, the final cat at the end of the pipeline is also a placeholder
for another process.
$ cat /tmp/abcdef.log | grep abc | cat
abcdef
xxxabc defxxx
$ cat /tmp/abcdef.log | unbuffer grep abc | cat
$ (cat /tmp/abcdef.log ; sleep 1) | unbuffer grep abc | cat
abcdef
xxxabc defxxx
$
BUGS
The man page is longer than the program.
SEE ALSO
"Exploring Expect: A Tcl-Based Toolkit for Automating Interactive Programs" by Don Libes, O'Reilly and Associates, January 1995.
AUTHOR
Don Libes, National Institute of Standards and Technology
1 June 1994 UNBUFFER(1)