ifconfig eth0 unplumb equivalent Post: 302724923

10 More Discussions You Might Find Interesting

1. IP Networking

Adding an IP to eth0

Hi there guys! I have a small task that I have to accomplish, but I don't seem to be able to do that. I have a server that I don't have physical access to, and I mostly control it with webmin. The server is running 2 websites. Both of these websites have their own domains that are linked to...

2. UNIX for Dummies Questions & Answers

ifconfig eth0 and awk and grep

if i have the command ifconfig eth0, what will the output be and how can i use either awk or grep to isolate and display the IP address, subnet mask and physical address of my host

3. IP Networking

what is "unplumb"

I saw an example on the web, it is an HP-UX command: ifconfig lan0 unplumb ifconfig lan0 plumb so what is plumb actually, I check HP-UX man page and still no idea. What is the difference if I do in this way? ifconfig lan0 down ifconfig lan0 up :confused:

4. Red Hat

ifcfg-eth0 and eth1 is N/A

when i finish installed rhel 4.4 to my hp dl585 box, ifcfg-eth0 and ifcfg-eth1 is not available.when i ifconfig -a,i can not see the eth0 and eth1, only lo0 and si0. Unlike to the other server i found eth0 and eth1 files in /etc/sysconfig/network-scripts/. what will i do?

5. UNIX for Dummies Questions & Answers

how can I find which one is eth0?

Hi, Just installed Centos 5.1 on HP DL360, on this system I have to close to ten nic's. How can I find which one is eth0? When I do " ifconfig -a" I see all of them, but I can't tell which is eth0? Please advice.

6. Red Hat

Device eth0 issue

Hi, I have just installed RHEL 5.4 on a BL430c-class server and I am attempting to connect to the network only when I try and start eth0, I get the following error? "Bringing up Interface eth0: hp device eth0 does not seem to be present, delaying initialization." I am using a HP...

7. Red Hat

VMBox not Recognizing eth0 on RH.

Hello, I re-installed my laptop and installed a new copy of VMBOX, I created a VM Machine with my Rhel5 and a CEntos copy as well. I am using a laptop HP DV4, I use wireless on the laptop. Usually when I boot up in to either machine I would get eht0 and lo as usual now I just don't get...

8. Red Hat

Eth0 Limitations

Hi, I have noticed some performance issues on my RHEL5 server but the memory and CPU utilization on the box is fine. I have a 1G full duplexed eth0 card and I am suspicious that this may be causing the problem. My eth0 settings are as follows: Settings for eth0: Supported ports: ...

9. IP Networking

iptables On for eth0 and off for other interfaces

Hi all, I am running a CentOS 6.4 box as an IDS and I need to configure one interface as the management interface which will require a firewall. However other ports (in promisc mode without IP) will have to be configured such that IPtables allows all traffic. I need to achieve this by editing...

10. Red Hat

Eth0 not running in redhat 6.4

Hi guys, I really need your help with this. My network interface eth0 is up but not running. I checked udev rules and ifcfg-eth0 files to make sure the mac address are the same. It just would not come up. Please please I will really appreciate the help here. Thank you in advance.

LEARN ABOUT DEBIAN

aoe-interfaces

aoe-interfaces(8)					      System Manager's Manual						 aoe-interfaces(8)

NAME

       aoe-interfaces - restrict aoe driver to specified network interfaces

SYNOPSIS

       aoe-interfaces [dev1] [dev2 ...]
       aoe-interfaces -c

DESCRIPTION

       The  aoe-interfaces command tells the aoe driver to ignore ATA over Ethernet (AoE) traffic on all but the specified network interfaces.	It
       is analogous to the aoe_iflist module load option.

       If neither the aoe_iflist module load option nor the aoe-interfaces command are used, the aoe driver will use any network interface for AoE
       traffic.   Using  aoe-interfaces  to limit AoE to only trusted networks prevents the case where a rogue AoE target appears on a public net-
       work, diverting data from the legitimate AoE target.  Such an imposter target effectively corrupts the data on the legitimate target.

       If the aoe driver is a module, then calling aoe-interfaces without arguments will display the current interfaces list.  If it  hasn't  been
       set then the output will be blank.

       It's good to run the aoe-discover command after setting the AoE interfaces list.

OPTIONS

       -c     The -c flag will clear the interface access list, permitting any interface to be used.

EXAMPLE

       In  this  example, the root user on a host named nai loads the aoe module with only eth0 allowable for AoE traffic.  After remembering that
       shelf 7 is on eth3, this sysadmin uses aoe-interfaces to add eth3 to the list of allowable network interfaces and then  calls  aoe-discover
       to ask the aoe driver to look for new AoE devices.

	      nai:~# modprobe aoe aoe_iflist="eth0"
	      nai:~# aoe-stat
		 e10.9		  eth0		    up
	      nai:~# aoe-interfaces eth0 eth3
	      nai:~# aoe-discover
	      nai:~# aoe-stat
		  e7.0		  eth3		    up
		  e7.1		  eth3		    up
		  e7.2		  eth3		    up
		  e7.3		  eth3		    up
		  e7.4		  eth3		    up
		  e7.5		  eth3		    up
		  e7.6		  eth3		    up
		  e7.7		  eth3		    up
		  e7.8		  eth3		    up
		  e7.9		  eth3		    up
		 e10.9		  eth0		    up
	      nai:~# aoe-interfaces
	      eth0 eth3

SEE ALSO

       aoe-discover(8), aoe-stat(8), aoetools(8).

AUTHOR

       Ed L. Cashin (ecashin@coraid.com)

																 aoe-interfaces(8)