Ive been having a play around with it as id really like the IP address to appear in the second column as per the headings. To do that, woul I have to play around with awk variables and print them all all at the end??
I asked a similar question earlier and got a very good answer but a new doubt came up. This is a few lines of a '/sbin/ifconfig' command on my PC:
RX packets:3781025 errors:0 dropped:0 overruns:0 frame:0
TX packets:1941909 errors:0 dropped:0 overruns:0 carrier:0
Does the RX and TX packets... (1 Reply)
I'm trying to install the recommended patch cluster on a x86 Solaris 10 box.
I get this error:
ERROR: /sbin/zonename cannot be found. install_cluster for 10_x86 patch cluster not applied. Exiting.
I tried touching the file and it gave a different error of: expected argument..
anyone... (1 Reply)
I am executing a stored proc and sending the results in a log file. I then want to grab one result from the output parameters (bolded below, 2) so that I can store it in a variable which will then be called in another script. There are more details that get printed in the beginning of the log file,... (3 Replies)
Hi -
Trying to understand a few things from an ifconfig -a output - can't seem to find info anywhere on the net.
Specifically - looking to understand the following:
Flags=8863
Smart
Running (is this the same as UP)
Simplex
inet6
supported media: autoselect - does that imply the... (1 Reply)
Hi,
I wish to format the output of a grep command in such a way that sed will be able to handle the newline characters held in the output.
Since sed does not allow newlines to be contained in a replacement pattern, that means adding a backslash '\' character to the end of each line from... (8 Replies)
Hi all,
Very new to shell scripting so appreciate some help!
There is a process count that I need to monitor, I have the AIX command that gives this value and I've cleaned it up with grep/awk so it only spits out the value I'm interested in:
echo "psc -i 10050 -s RELOAD_SERVICE" | tmadmin... (14 Replies)
I'm trying to gather information on the interfaces on a large number of servers.
If I run ifconfig I will get: eth0 Link encap:Ethernet HWaddr 00:50:56:A2:27:C1
inet addr:10.145.xxx.xxx Bcast:10.152.45.255 Mask:255.255.254.0
-----
eth1 Link... (2 Replies)
Hi,
I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Dear all,
I have below "ldapsearch" output
$ ldapsearch -D "CN=SVC-ACCOUNT,OU=SVC,OU=VDSI,OU=Non-Human,DC=Org,DC=com" -w secretword -H ldaps://org.com:636 -b DC=Org,DC=com -s sub uid=v00000 "(filter)" "displayName" "uid" "street"
# extended LDIF
#
# LDAPv3
# base <DC=Org,DC=com> with... (7 Replies)
Discussion started by: baluchen
7 Replies
LEARN ABOUT DEBIAN
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)