10-27-2012
Hello,
Please past "route -n" command for both system.
10 More Discussions You Might Find Interesting
1. IP Networking
We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command
64 bytes from 124.168.215.40:... (6 Replies)
Discussion started by: chrisanto_2000
6 Replies
2. IP Networking
Hello this is my first post at this forum.
Apologize for my lack of network understanding
but Im posting to learn.
I have a problem reaching default gateway 10.18.110.1
If I use my laptop I can ping 10.18.110.1 but with our red hat multihomed server the gateway does not respond to ping.
cat... (11 Replies)
Discussion started by: vettec3
11 Replies
3. Solaris
I was install new solaris10 on m4000 model after that i "ping -s" to default gateway but it's take longtime (2 Min) to reply and if i use "ping" only it's reply to fase(2 sec). any body who can tell me about my problem and how to fix it please. i'm try to fix several days. (2 Replies)
Discussion started by: cesmk
2 Replies
4. AIX
Hello,
I am new to Unix :D and have been trying to configure an AIX server running 5.3. I used smitty or smit to configure interface 0 on the server. I am able to ping the IP I set, however I am still unable to ping the gateway. I configured the IP by navigating to Communications Applications... (6 Replies)
Discussion started by: cdub50
6 Replies
5. Red Hat
I know the subject line is very similar to: destination host unreachable
but the problem with my machine appears to be somewhat different from that thread. apologies if I missed something from there.
We recently moved a machine physically and from one subnet to another . I used... (1 Reply)
Discussion started by: mirage
1 Replies
6. UNIX for Dummies Questions & Answers
I have NCR MP-RAS unix. I have been trying for several months to get our network working since we had never used it before. I have setup all routes that I can think of. I know it has something to do with the routing table, because out of sheer luck I was able to get it working, and than like a... (4 Replies)
Discussion started by: Rutgerncas
4 Replies
7. AIX
I just reinstalled a fresh install of 5300 07 on an old 44p model 170, after installing I set an IP Address on en2 and I tried to the ping default gateway, no response. I tried a
startsrc -g tcpip
... and then I can ping the default gateway. I broke the ping and tried again to ping. I cannot... (1 Reply)
Discussion started by: asyed123
1 Replies
8. AIX
Hi,
I installed AIX 7.1 on a blade though (hmc with vio). I can ping the IP address, but not the gateway. Is there anything that I should configure?
Is there anything that I have to check with vio setting or Am I missing any configuration?
Please let me know further.
Thank you (5 Replies)
Discussion started by: pjeedu2247
5 Replies
9. UNIX for Advanced & Expert Users
I have setup a Linux machine on my server but for some reason Im unable to reach my default gateway. This is causing me to not communicate with the outside world (unable to connect to CentOS repos)
# ifconfig
enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet... (3 Replies)
Discussion started by: Junaid Subhani
3 Replies
10. UNIX for Beginners Questions & Answers
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
LEARN ABOUT DEBIAN
make_sockdfr
MAKE_SOCKDFR(8) System Manager's Manual MAKE_SOCKDFR(8)
NAME
make_sockdfr - Generates frozen route file for SOCKS server
SYNOPSIS
make_sockdfr [infile [outfile] ]
DESCRIPTION
make_sockdfr reads in a plain-text route file for the SOCKS server and produces a frozen route file as the output.
Both arguments are optional. The default for infile is /etc/sockd.route; the default for outfile is /etc/sockd.fr. You may specify infile
while omitting outfile, but you cannot specify outfile without also speficying infile.
The contents of the frozen route file is essentially the memory image of the parsed input file. Using the frozen route file can reduce the
start-up delay of the SOCKS server program since it no longer has to parse the file contents.
When the SOCKS server starts, it always looks for the frozen route file /etc/sockd.fr first. If that file is not found, it then tries to
use the plain-text route file /etc/sockd.route. If you use frozen route file, you must remember to run make_sockdfr every time after you
modify the plain-text file or the SOCKS server will continue to use the frozen version of a previous route file.
To find out the contents of a frozen route file, use dump_sockdfr.
FILES
/etc/sockd.fr, /etc/sockd.route
SEE ALSO
dump_sockdfr(8), sockd.fr(5), sockd.route(5)
AUTHOR
Ying-Da Lee, yingda@esd.sgi.com or yingda@best.com
May 6, 1996 MAKE_SOCKDFR(8)