With cut -c 8-13 myfile,
I am getting some numeric value.
In my shell script I am trying to assign something like this,
var=cut -c 8-13 myfile
But at the time of execution I am getting -c is not found.
If I dont assign, then script executes well.
Can we not simply use the value from one... (8 Replies)
If I run this command
networksetup -listallnetworkservices
I get the following output.
Ethernet
AirPort
*Parallels Host-Guest
*Parallels NAT
MY VPN
Ethernet 2
I want to make changes to only anything that contains the word "Ethernet" which I can do with grep.
But What I really need a... (6 Replies)
Hi, with this command:
cu -l /dev/ttyACM0 -s 9600 > name.txt
I put the output of the port in a txt
Is posible to do the same (or similar) in a var directly, inside a C program?
cu -l /dev/ttyACM0 -s 9600 > variable ?
I have trying this withs pipes, but i dont know how to... (6 Replies)
Hi all
I run my program prog.c in the following way :
$ ./prog 1 > output.txt where 1 is a user defined initial value used by the program.
But now I want to run it for many a thousand initial values, 1-1000, and store all the outputs in different files.
Like
$ ./prog 1... (1 Reply)
I would like to redirect output of command line in for loop as $line.
Output should be processed as line but instead it throw whole output.
Could somebody help me on how to redirect output of command line and process it line by line without sending output to any file.
below is my code ... (1 Reply)
Hi,
I'd like to assign the output of the find command to a variable.
What I need is to run the find command, and if it returns zero files, the program exits.
so i'm trying to assign the output of the find command to the $var1 variable....and then if this is less than one, I echo a... (2 Replies)
Hi,
This is my input file
cat input
chr1:100-200
chr1:220-300
chr1:300-400
Now, I would like to run a program that will take each of the input record
for i in `cat input`; do program $i | wc -l;done
the output will be something like
10
20
30
But, I would like to print the... (4 Replies)
I'm very much a newbie and hence why this is going to be a stupid question.
I'm attempting to create a korn shell script that pulls zone file locations and includes the copy command in the output. What?
getzonedir.ksh
#!/bin/ksh
while read -r domain
do ls */*"$domain" > $dir1
echo "cp... (5 Replies)
In the else of the main if condition .
else
set lnk = $(readlink -f <path> | cut -d '/' -f7)
echo "$lnk"
if ]
When I run the above on command line , the execution seems to be fine and I get the desired output. But when I try to assign it to a variable within a loop... (12 Replies)
Discussion started by: sankasu
12 Replies
LEARN ABOUT DEBIAN
bup-margin
bup-margin(1) General Commands Manual bup-margin(1)NAME
bup-margin - figure out your deduplication safety margin
SYNOPSIS
bup margin [options...]
DESCRIPTION
bup margin iterates through all objects in your bup repository, calculating the largest number of prefix bits shared between any two
entries. This number, n, identifies the longest subset of SHA-1 you could use and still encounter a collision between your object ids.
For example, one system that was tested had a collection of 11 million objects (70 GB), and bup margin returned 45. That means a 46-bit
hash would be sufficient to avoid all collisions among that set of objects; each object in that repository could be uniquely identified by
its first 46 bits.
The number of bits needed seems to increase by about 1 or 2 for every doubling of the number of objects. Since SHA-1 hashes have 160 bits,
that leaves 115 bits of margin. Of course, because SHA-1 hashes are essentially random, it's theoretically possible to use many more bits
with far fewer objects.
If you're paranoid about the possibility of SHA-1 collisions, you can monitor your repository by running bup margin occasionally to see if
you're getting dangerously close to 160 bits.
OPTIONS --predict
Guess the offset into each index file where a particular object will appear, and report the maximum deviation of the correct answer
from the guess. This is potentially useful for tuning an interpolation search algorithm.
--ignore-midx
don't use .midx files, use only .idx files. This is only really useful when used with --predict.
EXAMPLE
$ bup margin
Reading indexes: 100.00% (1612581/1612581), done.
40
40 matching prefix bits
1.94 bits per doubling
120 bits (61.86 doublings) remaining
4.19338e+18 times larger is possible
Everyone on earth could have 625878182 data sets
like yours, all in one repository, and we would
expect 1 object collision.
$ bup margin --predict
PackIdxList: using 1 index.
Reading indexes: 100.00% (1612581/1612581), done.
915 of 1612581 (0.057%)
SEE ALSO bup-midx(1), bup-save(1)BUP
Part of the bup(1) suite.
AUTHORS
Avery Pennarun <apenwarr@gmail.com>.
Bup unknown-bup-margin(1)