We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command
64 bytes from 124.168.215.40:... (6 Replies)
Hello this is my first post at this forum.
Apologize for my lack of network understanding
but Im posting to learn.
I have a problem reaching default gateway 10.18.110.1
If I use my laptop I can ping 10.18.110.1 but with our red hat multihomed server the gateway does not respond to ping.
cat... (11 Replies)
I was install new solaris10 on m4000 model after that i "ping -s" to default gateway but it's take longtime (2 Min) to reply and if i use "ping" only it's reply to fase(2 sec). any body who can tell me about my problem and how to fix it please. i'm try to fix several days. (2 Replies)
Hello,
I am new to Unix :D and have been trying to configure an AIX server running 5.3. I used smitty or smit to configure interface 0 on the server. I am able to ping the IP I set, however I am still unable to ping the gateway. I configured the IP by navigating to Communications Applications... (6 Replies)
I know the subject line is very similar to: destination host unreachable
but the problem with my machine appears to be somewhat different from that thread. apologies if I missed something from there.
We recently moved a machine physically and from one subnet to another . I used... (1 Reply)
I have NCR MP-RAS unix. I have been trying for several months to get our network working since we had never used it before. I have setup all routes that I can think of. I know it has something to do with the routing table, because out of sheer luck I was able to get it working, and than like a... (4 Replies)
I just reinstalled a fresh install of 5300 07 on an old 44p model 170, after installing I set an IP Address on en2 and I tried to the ping default gateway, no response. I tried a
startsrc -g tcpip
... and then I can ping the default gateway. I broke the ping and tried again to ping. I cannot... (1 Reply)
Hi,
I installed AIX 7.1 on a blade though (hmc with vio). I can ping the IP address, but not the gateway. Is there anything that I should configure?
Is there anything that I have to check with vio setting or Am I missing any configuration?
Please let me know further.
Thank you (5 Replies)
I have setup a Linux machine on my server but for some reason Im unable to reach my default gateway. This is causing me to not communicate with the outside world (unable to connect to CentOS repos)
# ifconfig
enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet... (3 Replies)
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)