|
|
Sponsored Content
Operating Systems
Linux
Red Hat
Can not ping default gateway
Post 302719903 by aixlover on Tuesday 23rd of October 2012 10:29:45 AM
10-23-2012
|
|
10 More Discussions You Might Find Interesting
1. IP Networking
We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command
64 bytes from 124.168.215.40:... (6 Replies)
Discussion started by: chrisanto_2000
6 Replies
2. IP Networking
Hello this is my first post at this forum.
Apologize for my lack of network understanding
but Im posting to learn.
I have a problem reaching default gateway 10.18.110.1
If I use my laptop I can ping 10.18.110.1 but with our red hat multihomed server the gateway does not respond to ping.
cat... (11 Replies)
Discussion started by: vettec3
11 Replies
3. Solaris
I was install new solaris10 on m4000 model after that i "ping -s" to default gateway but it's take longtime (2 Min) to reply and if i use "ping" only it's reply to fase(2 sec). any body who can tell me about my problem and how to fix it please. i'm try to fix several days. (2 Replies)
Discussion started by: cesmk
2 Replies
4. AIX
Hello,
I am new to Unix :D and have been trying to configure an AIX server running 5.3. I used smitty or smit to configure interface 0 on the server. I am able to ping the IP I set, however I am still unable to ping the gateway. I configured the IP by navigating to Communications Applications... (6 Replies)
Discussion started by: cdub50
6 Replies
5. Red Hat
I know the subject line is very similar to: destination host unreachable
but the problem with my machine appears to be somewhat different from that thread. apologies if I missed something from there.
We recently moved a machine physically and from one subnet to another . I used... (1 Reply)
Discussion started by: mirage
1 Replies
6. UNIX for Dummies Questions & Answers
I have NCR MP-RAS unix. I have been trying for several months to get our network working since we had never used it before. I have setup all routes that I can think of. I know it has something to do with the routing table, because out of sheer luck I was able to get it working, and than like a... (4 Replies)
Discussion started by: Rutgerncas
4 Replies
7. AIX
I just reinstalled a fresh install of 5300 07 on an old 44p model 170, after installing I set an IP Address on en2 and I tried to the ping default gateway, no response. I tried a
startsrc -g tcpip
... and then I can ping the default gateway. I broke the ping and tried again to ping. I cannot... (1 Reply)
Discussion started by: asyed123
1 Replies
8. AIX
Hi,
I installed AIX 7.1 on a blade though (hmc with vio). I can ping the IP address, but not the gateway. Is there anything that I should configure?
Is there anything that I have to check with vio setting or Am I missing any configuration?
Please let me know further.
Thank you (5 Replies)
Discussion started by: pjeedu2247
5 Replies
9. UNIX for Advanced & Expert Users
I have setup a Linux machine on my server but for some reason Im unable to reach my default gateway. This is causing me to not communicate with the outside world (unable to connect to CentOS repos)
# ifconfig
enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet... (3 Replies)
Discussion started by: Junaid Subhani
3 Replies
10. UNIX for Beginners Questions & Answers
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
LEARN ABOUT SUNOS
jms-ping
asadmin-jms-ping(1AS) User Commands asadmin-jms-ping(1AS) NAME
jms-ping - checks to see if the JMS provider is up and running SYNOPSIS
jms-ping --user admin_user [--password admin_password] [--host localhost] [--port 4848] [--passwordfile filename] [--secure|-s] [--terse=false] [--echo=false] [--interactive=false] Checks to see if the JMS provider is up and running. This command is supported in remote mode only. OPTIONS
--user authorized domain application server administrative username. --password password to administer the domain application server. --host machine name where the domain application server is running. --port port number of the domain application server listening for administration requests. --passwordfile file containing the domain application server password. --secure if true, uses SSL/TLS to communicate with the domain application server. --terse indicates that any output data must be very concise, typically avoiding human-friendly sentences and favoring well- formatted data for consumption by a script. Default is false. --echo setting to true will echo the command line statement on the standard output. Default is false. --interactive if set to true (default), only the required password options are prompted. Example 1: Using jms-ping asadmin> jms-ping --user admin --password adminadmin --host bluestar --port 4848 server1 JMS Ping Status=RUNNING EXIT STATUS
0 command executed successfully 1 error in executing the command asadmin-create-jmsdest(1AS), asadmin-delete-jmsdest(1AS), asadmin-list-jmsdest(1AS) J2EE 1.4 SDK March 2004 asadmin-jms-ping(1AS)