NIC card issue Post: 302713839

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

No NIC Card?

Hello Everyone, While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use. There is no output for dmesg|grep eth. Does that mean that mandrake...

2. HP-UX

configuring nic card

using sam i have tryed to configure the nic, however when i try to do so i get an error saying i couldn't as i was using BIND ?

3. Linux

Howto Detect New Nic Card

Hi PPL! I have P-IV processor, with on-board NIC card. I have added one more NIC card for domestic use. My kudzu does not recognise the newly added PCMCIA NIC card. How to go about this one? Suggest PEnguin

4. HP-UX

how can I determine which NIC card is virtual NIC Card

how can I determine which NIC card is virtual NIC Card which condition can make a decision Does HP UX have Virtual Network Adapter Concept if ,it has where I can Find if I Install Virutal Network Adapter or which command that i can get it or which software can generate thanks

5. Solaris

Reg. NIC card

Hi friends i have problem with my home pc, i installed solaris 10 but my lan drivers are not installed, if i want to install drivers manually from where to download and how to install. I have Realtech lan card. when i type ifconfig -a it shows only localhost 127.0.0.0 Lo0 cannot see other than...

6. UNIX for Dummies Questions & Answers

NIC card monitoring traffic question

Folks; I have 2 NIC cards on my SUSE Linux server. One of them was reporting receive errors for a while now it's OK, but i'd like to monitor it. Is there any command i can run to tell me the usage in the past or give me a history of traffic and the speed that going on this specific card? I...

7. Solaris

NIC card repetative Failover

I have configure 2 NIC in ipmp group1 .Similarly other 2 NIC in ipmp group2 When I connect both NIC to 2 different switch , which is connect to one L3 switch as trunk. Both the NIC failover to each other continously. Following are the message log. ifmsdb1 in.mpathd: NIC failure detected...

8. Linux

changing speed of NIC Card in linux

Hi, I would like to know how to change the speed of ethernet card in linux? as it is showing auto-neg using mii-tool -v eth0 and my requirement is 100mbps full duplex. Regards, Manoj

9. Linux

How to check which NIC Card is used for backups?

I have a linux box with 2 nic cards on it one for prod and one for backup. My question is while the backup are happening how do I determine which nic is used for backups . I would like to run a command so that that I can see the usage in a dynamic fashion.

10. Red Hat

Finding speed of NIC Card

Hi, I would like to know how to find out ACTUAL speed of NIC Card. I have used the command ethtool eth0, it is showing supported modes, but what is acutal speed ? how to find out?

LEARN ABOUT LINUX

my

MY(4)                                                      BSD Kernel Interfaces Manual                                                      MY(4)

NAME

     my -- Myson Technology Ethernet PCI driver

SYNOPSIS

     To compile this driver into the kernel, place the following line in your kernel configuration file:

           device my

     Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

           if_my_load="YES"

DESCRIPTION

     The my driver provides support for various NICs based on the Myson chipset.  The Myson chipset is a variant of the DEC Tulip NIC chipset.

     The driver will work with almost any MII-compliant PHY, thus failure to positively identify the chip is not a fatal error.

HARDWARE

     The my driver provides support for various NICs based on the Myson chipset.  Supported models include:

     o   Myson MTD800 PCI Fast Ethernet chip
     o   Myson MTD803 PCI Fast Ethernet chip
     o   Myson MTD89X PCI Gigabit Ethernet chip

SEE ALSO

     altq(4), de(4), netintro(4), pci(4), ifconfig(8)

HISTORY

     The my driver first appeared in FreeBSD 4.6.

AUTHORS

     The my driver was written by Myson Technology Inc.

     This manual page was written by Hiten M. Pandya <hmp@FreeBSD.org>.

BUGS

     The my driver does not support Power Management Events (PME).

BSD                                                               March 11, 2007                                                               BSD